Design and Test of Rice Hill-drop Seed Metering Device Embedded with Rotating Air Cavity

被引：0
作者：
Wan L. [1 ,2 ]
Wang H. [1 ]
Che G. [1 ,2 ]
机构：
[1] College of Engineering, Heilongjiang Bayi Agricultural University, Daqing
[2] Heilongjiang Provincial Key Laboratory of Agricultural Machinery Intelligent Equipment, Daqing
来源：
Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery | 2019年 / 50卷 / 11期
关键词：
Design; Hole direct seeding; Rice; Rotating air cavity; Seed metering device; Test;
D O I：
10.6041/j.issn.1000-1298.2019.11.008
中图分类号：
学科分类号：
摘要：
Aiming at the problems of inadequate use of air pressure for air suction type metering device, friction between seed plate rotation and rubber pad, and poor uniformity of hole sowing, airflow field of rice seed metering device embedded with rotating air chamber was designed by the absorption principle. The working principle of each stage of seed metering device was introduced, and the parameters and structure of the key components were designed. Based on the basic governing equation of fluid, the negative pressure cavity was simulated by ANSYS software. The numerical simulation was carried out with the influence factors of pore diameter and position distribution of suction hole. The average pressure of the cavity and the average velocity of the suction hole were the evaluation indexes. The simulation results showed that the distribution of flow field in air cavity was relatively stable, which provided a stable negative pressure environment for seed suction. The JPS-12 test-bed was applied to verify the simulation test. Taking the rotation velocity of air chamber, the negative pressure of air chamber and the height of seed filling as the influencing factors, and taking the qualified rate of rice sowing, the rate of missed sowing and the rate of re-sowing as the evaluation indexes, the experiment of quadratic rotation combination design at five levels of factors was carried out. Using Design-Expert 8.0.6 to complete variance analysis and significance test, the regression equation and the corresponding surface map were obtained, the interaction of various factors was analyzed, and the best parameters were determined. Number combination: when the rotating velocity of the air chamber was 21.61 r/min, the negative pressure of the air chamber was 4.4 kPa and the seed filling height was 15.7 cm, the performance of the operation was 93.6% for the qualified index, 3.47% for the missed broadcast index and 2.93% for the replay index. The experimental results of bench test were in good agreement with the optimized results, which met the requirement of direct seeding of japonica rice. © 2019, Chinese Society of Agricultural Machinery. All right reserved.
引用
收藏
页码：74 / 84
页数：10
相关论文
共 25 条
[1]  
Zeng S., Tang H., Luo X., Et al., Design and test of simultaneous furrow ridging and fertilization of rice precision hole direct seeding machine, Transactions of the CSAE, 28, 20, pp. 12-19, (2012)
[2]  
Zhang G., Zang Y., Luo X., Et al., Design and test of rice pneumatic seed puller oriented seed stirring device, Transactions of the CSAE, 29, 12, pp. 1-8, (2013)
[3]  
Wang Z., Luo X., Tang X., Et al., Rice precision hole direct seeding technology and tools based on the combination of agricultural machinery and agronomy, Journal of South China Agricultural University, 31, 1, pp. 91-95, (2010)
[4]  
Zang Y., Luo X., Zhou Z., Et al., Development strategy of rice planting and harvesting mechanization in south China, Transactions of the Chinese Society for Agricultural Machinery, 39, 1, pp. 60-63, (2008)
[5]  
Luo X., Liu T., Jiang E., Et al., Design and experiment of seed row wheel for direct seeding of rice jingliang hole, Transactions of the CSAE, 23, 3, pp. 108-112, (2007)
[6]  
Zhang X., Li L., Wang C., Et al., Precision planter of 2BS-420 rice seedling tray, Transactions of the Chinese Society for Agricultural Machinery, 44, 6, pp. 56-61, (2013)
[7]  
Zhang X., Xia L., Ma H., Et al., Reliability of precision seeder, Transactions of the Chinese Society for Agricultural Machinery, 35, 2, pp. 62-64, (2004)
[8]  
Zhang K., Yi S., Simulation and experimental optimization of seed filling performance of air-suction drum type corn seeder, Transactions of the Chinese Society for Agricultural Machinery, 48, 7, pp. 78-86, (2017)
[9]  
Wang Y., Jin Y., Luo S., Et al., Design and test of concentrated row type soybean seed distributor, Transactions of the Chinese Society for Agricultural Machinery, 49, 6, pp. 112-118, (2018)
[10]  
Chen Y., Jia H., Wang J., Et al., Design and test of high speed precision soybean planter with protruding spoon, Transactions of the Chinese Society for Agricultural Machinery, 48, 8, pp. 95-104, (2017)
123