Measurement and analysis of machining induced tribological characteristics in dual jet minimum quantity lubrication assisted turning of duplex stainless steel

被引：56

作者：

Kumar Gupta M. ^{[1
]}

Boy M. ^{[2
]}

Erdi Korkmaz M. ^{[3
]}

Yaşar N. ^{[4
]}

Günay M. ^{[3
]}

Krolczyk G.M. ^{[1
]}

机构：

[1] Faculty of Mechanical Engineering, Opole University of Technology, 76 Proszkowska St., Opole

[2] TOBB Vocational High School, Karabük University, Karabük

[3] Department of Mechanical Engineering, Karabük University, Karabük

[4] Yenice Vocational High School, Karabük University, Karabük

来源：

Measurement: Journal of the International Measurement Confederation | 2022年 / 187卷

关键词：

Cooling; Duplex steel; Machining; Measurement; Minimum quantity lubrication; Tribology;

D O I：

10.1016/j.measurement.2021.110353

中图分类号：

学科分类号：

摘要：

In this work, the sustainable machining approach is promoted by implementing the dry and minimum quantity lubrication (MQL) cooling conditions in the turning of duplex stainless steel. Initially, the turning experiments were performed under dry as well as MQL conditions and then, the influence of different positions of MQL nozzles on tribological and machining performance of 2205 duplex steel was investigated. The cutting parameters were kept fixed and the performance is evaluated in terms of surface roughness, micro-hardness, energy consumption, tool wear, machined surface microstructure and chips morphology. The results demonstrated that the highest average surface roughness values were obtained under dry conditions, with a value of 2.20 µm while MQL (flank + rake directions) produces the lowest surface roughness value of 1.55 µm with an improvement of 30%. Moreover, dual-jet MQL gives the lowest energy consumption (229 kJ) and tool wear (0.15 mm) with 23.67% and 52.38% enhancement, respectively. © 2021 Elsevier Ltd

引用

共 64 条

[1]

Khanna N., Shah P., Chetan, Chetan, Comparative analysis of dry, flood, MQL and cryogenic CO2 techniques during the machining of 15–5-PH SS alloy, Tribol. Int., 146, (2020)

[2]

Korkmaz M.E., Verification of Johnson-Cook parameters of ferritic stainless steel by drilling process: Experimental and finite element simulations, J. Mater. Res. Technol., 9, 3, pp. 6322-6330, (2020)

[3]

Liu H., Sun J., Qian J., Wang B., Shi S., Zhu Y., Wang Y., Neville A., Hua Y., Revealing the temperature effects on the corrosion behaviour of 2205 duplex stainless steel from passivation to activation in a CO2-containing geothermal environment, Corros. Sci., 187, (2021)

[4]

Koyee R.D., Eisseler R., Schmauder S., Application of Taguchi coupled Fuzzy Multi Attribute Decision Making (FMADM) for optimizing surface quality in turning austenitic and duplex stainless steels, Measurement., 58, pp. 375-386, (2014)

[5]

Gokce H., Modelling and Optimization for Thrust Force, Temperature and Burr Height in Drilling of Custom 450, Exp. Tech., (2021)

[6]

Gunay M., Meral T., Korkmaz M.E., (2018)

[7]

Krolczyk G.M., Nieslony P., Legutko S., Determination of tool life and research wear during duplex stainless steel turning, Arch. Civ. Mech. Eng., 15, pp. 347-354, (2015)

[8]

Krolczyk G.M., Nieslony P., Maruda R.W., Wojciechowski S., Dry cutting effect in turning of a duplex stainless steel as a key factor in clean production, J. Clean. Prod., 142, pp. 3343-3354, (2017)

[9]

Gowthaman P.S., Jeyakumar S., Saravanan B.A., Machinability and tool wear mechanism of Duplex stainless steel – a review, Mater. Today Proc., 26, pp. 1423-1429, (2020)

[10]

J R., N A., A comprehensive investigation on the effect of flood and MQL coolant on the machinability and stress corrosion cracking of super duplex stainless steel, J. Mater. Process. Technol., 276, (2020)

← 1 2 3 4 5 6 7 →