Research on Vibration Reduction Characteristics of Straight Section of Metro Track with Damping Wheel

被引：0

作者：

Wu Q. ^{[1
]}

Qi M. ^{[2
]}

Zhou X. ^{[1
,2
]}

Wang A. ^{[1
]}

机构：

[1] School of Urban Railway Transportation, Shanghai University of Engineering Science, Shanghai

[2] State Key Laboratory of Traction Power, Southwest Jiaotong University, Chengdu

来源：

Jixie Gongcheng Xuebao/Journal of Mechanical Engineering | 2022年 / 58卷 / 22期

关键词：

damping wheel; dynamic characteristics; field test; straight metro track; vibration reduction;

D O I：

10.3901/JME.2022.22.395

中图分类号：

学科分类号：

摘要：

A study on the vibration reduction characteristics of damping wheel operating on the straight section is carried out using linear motors vehicles under normal and bad wheel/rail conditions through field experiment and numerical simulation. The field test obtains the vibration characteristics of the track components and the tunnel wall under the normal conditions. The test results show that the damping wheel has a good suppression effect on the vibration of the track infrastructure, and its damping effect can reach up to 2-3 dB vibration reduction. The damping wheel also has a good vibration damping effect on the wheel polygonal impact vibration. Since then, in order to further explore the vibration reduction effect of the damping wheel in the extreme conditions(geometric defects of welded rail joint and rail corrugation), a vehicle-track coupling dynamics model is established to numerically simulate the vibration characteristics of the track parts and the tunnel wall when the train with the damping wheels passes through the rails with the welded joint geometry and the corrugation. In the model, the damping wheels is considered to be composed of three parts: wheel core, left rim and right rim, each of which is taken into account 6 degrees of freedom, and the core and rim are connected by using pressing rubber layer. The simulation results show that the damping wheel has a better vibration reduction effect on the rail in the situation of serious geometric defects at rail welded joint and serious rail corrugation, and its damping effect can reach up to 4-7 dB. in which the higher the running speed, the more obvious the vibration reduction effect is. © 2022 Editorial Office of Chinese Journal of Mechanical Engineering. All rights reserved.

引用

页码：395 / 405

页数：10

共 19 条

[1]

HE Yanfang, Research on rail disease detection and identification of urban rail transit, (2016)

[2]

XIAO Gan, GAO Xueshan, CHANG Chao, Influence of rail grinding on wheel/rail profile matching and rail vibration response characteristics[J], Journal of the China Railway Society, 43, 2, pp. 125-133, (2021)

[3]

WANG Wenbin, LIU Weining, JIA Yinxuan, Et al., Research on ground vibration caused by subway operation before and after replacement of damping coupler[J], China Railway Science, 31, 1, pp. 87-92, (2010)

[4]

LI Qianjin, CHEN Jianguo, Research on environmental vibration and control caused by rail transit[J], China Railway, 4, pp. 58-61, (2009)

[5]

GUO Chao, Research on vibration abatement performance and maintenance analysis of steel spring floating plate road bed, (2017)

[6]

ZHAO Yue, WANG Ruigan, LI Muxiao, Et al., Time-domain modeling analysis of roar noise in tram and embedded track curves [J], Journal of Mechanical Engineering, 57, 2, pp. 158-168, (2021)

[7]

ZHANG Baojun, Research on impact noise characteristics of elastic wheel in Metro, (2021)

[8]

LU Qibo, Research on vibration and noise reduction performance of elastic vehicle, (2014)

[9]

PENG Hua, SUN Tianchi, CAI Xiaopei, Et al., Characteristics and dynamic effects of rail corrugation in subway short-pillow integral trackbed sections[J], Railway Architecture, 62, 2, pp. 69-74, (2022)

[10]

ZHOU Xin, HAN Jian, ZHOU Xin, Et al., Analysis of vibration and noise reduction characteristics of elastic wheel[J], Journal of the China Railway Society, 37, 6, pp. 48-53, (2015)

← 1 2 →