Reviews in dynamic characteristics of rolling interface and vibration test/suppression methods of the rolling mill

被引:0
|
作者
Fan X.-B. [1 ]
Li H. [1 ]
Jiang Y. [2 ]
Fan B.-X. [3 ]
Li L.-J. [4 ]
机构
[1] School of Mechanical and Power Engineering, Henan Polytechnic University, Jiaozuo
[2] Harbin Research Institute of Electrical Instruments, Harbin
[3] School of Economics and Management, Henan Polytechnic University, Jiaozuo
[4] Jiaozuo Hongye Vehicle Co., Ltd. Jiaozuo, Henan
关键词
Dynamic characteristics; Rolling interface; Rolling mill; Vibration signals; Vibration suppression; Vibration test;
D O I
10.2174/1872212114999200918121801
中图分类号
学科分类号
摘要
Background: Rolling mill vibration mechanism is very complex, and people have not found a satisfactory vibration control method. Rolling interface is one of the vibration sources of the rolling mill system, and its friction and lubrication state has a great impact on the vibration of the rolling mill system. It is necessary to establish an accurate friction model for the unsteady lubrication process of the roll gap and a nonlinear vibration dynamic model for the rolling process. In addition, it is necessary to obtain more direct and real rolling mill vibration characteristics from the measured vibration signals, and then study the vibration suppression method and design the vibration suppression device. Methods: This paper summarizes the friction lubrication characteristics of the rolling interface and its influence on rolling mill vibration, as well as the dynamic friction model of the rolling interface, the tribological model of the unsteady lubrication process of the roll gap, the non-linear vibration dynamic model of the rolling process, the random and non-stationary dynamic behavior of rolling mill vibration, etc. At the same time, the research status of rolling mill vibration testing technology and vibration suppression methods were summarized. Time-frequency analysis of non-stationary vibration signals was reviewed, such as wavelet transform, Wigner-Ville distribution, empirical mode decompo-sition, blind source signal extraction, rolling vibration suppression equipment development. Results: The lubrication interface of the roller gap under the vibration state presents unsteady dynamic characteristics. The signals generated by the vibration must be analyzed in time and frequency simultaneously. In the aspect of vibration suppression of the rolling mill, the calculation of inherent characteristics should be carried out in the design of the rolling mill to avoid dynamic defects such as resonance. When designing or upgrading the mill structure, it is necessary to optimize the structure of the work roll bending and roll shifting system, such as designing and developing the automatic adjustment mechanism of the gap between the roller bearing seat and the mill stand, add-ing floating support device to the drum shaped toothed joint shaft, etc. In terms of rolling technolo-gy, rolling vibration can be restrained by improving roll lubrication, reasonably distributing the rolling force of each rolling mill, reducing the rolling force of vibration prone rolling mill, increasing entrance temperature, reducing rolling inlet tension, reducing strip outlet temperature and reasonably arranging roll diameter. The coupling vibration can also be suppressed by optimizing the hydraulic servo system and the frequency conversion control of the motor. Conclusion: Under the vibration state, the lubrication interface of the roll gap presents unsteady dynamic characteristics. The signal generated by vibration must be analyzed by time-frequency dis-tribution. In the aspect of vibration suppression of the rolling mill, the calculation of inherent characteristics should be carried out in the design of the rolling mill to avoid dynamic defects such as resonance. It is necessary to optimize the structure of work roll bending and roll shifting system, when designing or reforming the mill structure. In the rolling process, rolling vibration can be restrained by improving roll lubrication, reasonably distributing the rolling force of each rolling mill, increasing billet temperature, reasonably arranging roll diameter and reducing rolling inlet tension. Through the optimization of the hydraulic servo system and the frequency conversion control of the motor, the coupling vibration can be suppressed. The paper has important reference significance for vibration suppression of continuous rolling mill and efficient production of high quality strip products. © 2021 Bentham Science Publishers.
引用
收藏
相关论文
共 50 条
  • [41] A study of nonlinear coupling dynamic characteristics of the cold rolling mill system under different rolling parameters
    Xu, Hai
    Cui, Ling-Li
    Shang, De-Guang
    ADVANCES IN MECHANICAL ENGINEERING, 2017, 9 (07):
  • [42] Mechanism research of rolling mill coupled vibration
    Wang, Ruipeng
    Peng, Yan
    Zhang, Yang
    Sun, Jianliang
    Peng, Y. (pengyan@ysu.edu.cn), 1600, Chinese Mechanical Engineering Society (49): : 66 - 71
  • [43] Rolling mill system dynamic design
    Li, M.
    Liu, H.
    Zhang, Y.
    Zhao, Y.
    Wany, Y.
    Li, A.
    Pei, Q.
    Zhao, L.
    Zou, L.
    Zhou, B.
    Chinese Journal of Mechanical Engineering (English Edition), 2001, 14 (04): : 373 - 377
  • [44] Rolling process and its influence analysis on hot continuous rolling mill vibration
    Xiaobin Fan
    Yong Zang
    Ke Jin
    Applied Physics A, 2016, 122
  • [45] ROLLING MILL SYSTEM DYNAMIC DESIGN
    Li Mouwei
    Chinese Journal of Mechanical Engineering(English Edition), 2001, (04) : 373 - 377
  • [46] Rolling process and its influence analysis on hot continuous rolling mill vibration
    Fan, Xiaobin
    Zang, Yong
    Jin, Ke
    APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING, 2016, 122 (12):
  • [47] Research of H∞ control and its application on suppression torsional vibration of rolling mill system
    Yu, Liye
    Xu, Lin
    Wang, Jianhui
    Gu, Shusheng
    Xu, Meirong
    WCICA 2006: SIXTH WORLD CONGRESS ON INTELLIGENT CONTROL AND AUTOMATION, VOLS 1-12, CONFERENCE PROCEEDINGS, 2006, : 6392 - +
  • [48] H∞ filter and load observer based compensative control for vibration suppression of rolling mill
    Fu, Jian
    Yang, Weidong
    Li, Boqun
    Zhang, Haijun
    Ge, LiangSong
    WCICA 2006: SIXTH WORLD CONGRESS ON INTELLIGENT CONTROL AND AUTOMATION, VOLS 1-12, CONFERENCE PROCEEDINGS, 2006, : 2209 - 2213
  • [49] Study on the effect of rolling mill dynamic stiffness on coupled vibration of hydraulic machine
    Wang, Lidong
    Hou, Peng
    Wang, Shen
    Wang, Chengzhen
    Yan, Xiaoqiang
    Wang, Xiaoling
    JOURNAL OF VIBROENGINEERING, 2024, 26 (03) : 455 - 468
  • [50] Influence of Vibration Characteristics on Dynamic Behavior of Rolling Agricultural Tires
    Fujita, Katsuhide
    Saito, Takashi
    Kaneko, Mitsugu
    DYNAMICS FOR SUSTAINABLE ENGINEERING, 2011, VOL 4, 2011, : 1945 - 1953