Investigation of machinability characteristics on C45 steel with cryogenically treated M2 HSS tool using statistical technique

被引：4
|
作者：
Kumar S. [1 ]
Ahmed M.R. [2 ]
Lokesha M. [3 ]
Manjunath L.H. [1 ]
机构：
[1] School Mechanical Engineering, REVA University, Bangalore
[2] School of Electronics and Communication Engineering, REVA University, Bangalore
[3] Department of Mechanical Engineering, MITE, Moodbidri, Mangalore
来源：
International Journal for Simulation and Multidisciplinary Design Optimization | 2019年 / 10卷
关键词：
Deep cryogenic treatment; Flank wear; Hardness; M2 HSS tool; Machining;
D O I：
10.1051/smdo/2019006
中图分类号：
学科分类号：
摘要：
The machining industries always eye on increasing hardness and reducing the friction at the cutting tool-workpiece interface to reduce flank wear, thereby enhancing the tool life. The present study investigates the effect of deep cryogenic treatment (DCT) on the behavior of M2 HSS tool in turning of C45 medium carbon steel. The tool is double tempered and is tested for hardness and flank wear. The power consumption is also analyzed in the process with a focus on green machining. While Taguchi's L27 orthogonal array (OA) is used to study the main interaction effect of all machining parameters, analysis of variance (ANOVA) and signal to noise (S/N) ratio are used for analysis of experimental outcomes. The study reveals that DCT has enhanced the hardness of HSS tool by 14.9%, while speed and feed were the dominating factors on the flank wear. Microstructure morphology using SEM is also discussed. © 2019 S. Kumar et al., published by EDP Sciences.
引用
收藏
相关论文
共 45 条
  • [31] Some Analysis into 0.18%-C Steel Work Piece Undergone through Turning Operation by Using HSS [KT-8 (M42)] Single Point Tool
    Dewangan, Saurabh
    Pattnayak, Ashutosh
    Abhishek, R.
    Patel, Niranjan
    1ST INTERNATIONAL CONFERENCE ON ADVANCES IN MECHANICAL ENGINEERING AND NANOTECHNOLOGY (ICAMEN 2019), 2019, 2148
  • [32] Quantification and localization of the liquid zone of partially remelted M2 tool steel using X-ray microtomography and scanning electron microscopy
    Gu, G. C.
    Pesci, R.
    Becker, E.
    Langlois, L.
    Bigot, R.
    Scheel, M.
    ACTA MATERIALIA, 2012, 60 (03) : 948 - 957
  • [33] An Investigation of the Effect of Surface Integrity and Layer Thickness Using T90Mn2W50Cr45 Tool Steel
    Rajendran, S.
    Sakthivel, M.
    Dharamalingam, S.
    MATERIALS AND MANUFACTURING PROCESSES, 2015, 30 (02) : 199 - 203
  • [34] Effect of Aluminum Addition to Nb-Al-C-N Coatings on AISI M2 Steel Obtained by Thermo-Reactive Deposition Technique
    Abakay, E.
    Sen, S.
    Sen, U.
    ACTA PHYSICA POLONICA A, 2016, 129 (04) : 653 - 655
  • [35] Inhibition of grain and precipitate growth of AISI M2 type tool steel powders by low-temperature nitriding using flowing ammonia gas
    Correia, JB
    Shohoji, N
    ISIJ INTERNATIONAL, 1996, 36 (03) : 363 - 365
  • [36] INVESTIGATION INTO STATISTICAL CHARACTERISTICS OF BUBBLES IN 2-PHASE FLOW .1. FUNDAMENTALS OF INSTRUMENTATION USING ELECTRIC RESISTIVITY PROBE TECHNIQUE
    SEKOGUCHI, K
    FUKUI, H
    MATSUOKA, T
    NISHIKAWA, K
    BULLETIN OF THE JSME-JAPAN SOCIETY OF MECHANICAL ENGINEERS, 1975, 18 (118): : 391 - 396
  • [37] Tribological and dry machining evaluation of superhard TiB2/TiC multilayer coatings deposited on Si(001), M2 steel, and C3WC cutting tool inserts using magnetron sputtering
    Lee, KW
    Chung, YW
    Korach, C
    Keer, LM
    SURFACE & COATINGS TECHNOLOGY, 2005, 194 (2-3): : 184 - 189
  • [38] Machinability investigation of Chromoly steel using TiN/Al2O3/TiCN/TiOCN multilayer coated tungsten carbide tool inserts with artificial neural network methodology
    Singh, Nikhil
    Bharatish, A.
    Rajkumar, G. R.
    Babu, G. Satheesh
    APPLIED RESEARCH, 2023, 2 (04):
  • [39] High-temperature tribology of Hf doped c-Al0.64Ti0.36N cathodic arc PVD coatings deposited on M2 tool steel
    Mondragon-Rodriguez, G. C.
    Hernandez-Mendoza, J. L.
    Gomez-Ovalle, A. E.
    Gonzalez-Carmona, J. M.
    Ortega-Portilla, C.
    Camacho, N.
    Hurtado-Macias, A.
    Espinosa-Arbelaez, D. G.
    Alvarado-Orozco, M.
    SURFACE & COATINGS TECHNOLOGY, 2021, 422 (422):
  • [40] Diffusion measurements using the shear cell technique: Investigation of the role of Marangoni convection by pre-flight experiments on the ground and during the Foton M2 mission
    Rosu-Pflumm, Raluca
    Wendl, Wolfgang
    Mueller-Vogt, German
    Suzuki, Shinsuke
    Kraatz, K. -H.
    Frohberg, G.
    INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2009, 52 (25-26) : 6042 - 6049
12345