Preparation and Characterization of TiO2 / Organic Silica Sol Modified Fluorinated Poly(styrene-acrylate) Emulsion

被引：0
|
作者：
Shi S. [1 ]
An Q. [1 ]
Qiu J. [1 ]
机构：
[1] Shaanxi Provincial Key Laboratory of Light Chemical Additives, School of Chemistry and Chemical Engineering, Shaanxi University of Science and Technology, Xi'an
来源：
Cailiao Daobao/Materials Reports | 2023年 / 37卷 / 08期
关键词：
emulsion polymerization; fluorinated styrene acrylic emulsion; hydrophobicity; thermal stability; TiO[!sub]2[!/sub] / organosilicon modification;
D O I：
10.11896/cldb.21110053
中图分类号：
学科分类号：
摘要：
In order to improve the hydrophobicity, thermal stability and mechanical properties of the fluorine-containing styrene-acrylic emulsion, Using butyl titanate (TＢT) and γ-methacryloyloxypropyltrimethoxysilane (KH-570) as raw materials, TiO2 / organosilica sol (TS) was prepared by sol-gel method. With butyl acrylate (ＢA), styrene (ST), dodecafluoroheptyl methacrylate (G04) and other acrylic functional monomers as the main raw materials through semi-continuous feeding method and seed emulsion polymerization, a fluorine-containing styrene-acrylic emulsion (TS-ＢHSAG) modified by TiO2 / organosilicon sol was prepared. The effects of different TS contents on the emulsion conversion were discussed. The structure composition and application properties of the emulsion and latex film were studied by FTIR, nanometer particle size analyzer, stability analyzer, XPS, XRD, SEM, AFM, and TGA. The results show that when the TS content gradually increased, the emulsion conversion rate and stability showed a continuous downward trend. As the TS content increase, the average particle size of the emulsion increased from 55.58 nm to 106.16 nm. FTIR and XPS results show that Si-O-Si, Si-O-Ti, CF2 bonds were formed in the TS-ＢHSAG latex film, confirming the fact that preliminary synthesis of TS has been achieved, and it has been introduced into the polymer with G04. XRD results show that TS was dispersed in the acrylic resin matrix in an amorphous phase. It was observed by SEM and AFM that TS nanoparticles formed a peak-like rough structure on the surface of the latex film, which enhanced the hydrophobicity. TGA results show that when the thermal weight loss is 10％ and 50％, the thermal decomposition temperatures of TS-ＢHSAG are 380.59 ℃ and 415.39 ℃, while at 600 ℃ the residual content increased from 4.78％ to 8.56％. When the amount of TS added is 3％, the contact angle of the TS-ＢHSAG latex film is 121°, the adhesion is grade 1, the impact resistance is 50 cm, the hardness is 2H, and the water absorption rate is 6.1％. © 2023 Cailiao Daobaoshe/ Materials Review. All rights reserved.
引用
收藏
相关论文
共 26 条
  • [1] Ni W N, You B, Tang L Y., Materials protection, 51, 4, (2018)
  • [2] Du Y B, Zhu L Q, Liu H C., Journal of Beijing University of Aeronautics and Astronautics, 10, (2004)
  • [3] Zhang Z M, Chen Y, Sun Z X., Surface Technology, 50, 1, (2021)
  • [4] Luo H, Ding J, Huang Z, Et al., Composites part B:Engineering, 155, (2018)
  • [5] Yu S W, Xiao S J, Zhang P B, Et al., Advanced Materials Research, 750, (2013)
  • [6] Guan Y D, Sun C L, Zhang S Z., plating & Finishing, 32, 5, (2013)
  • [7] Yang L L, Su Q X, Di K Y., paint Industry, 49, 9, (2019)
  • [8] Zhang T T, Yin J L, Su Q X., polyurethane Industry, 34, 3, (2019)
  • [9] Wang Z X, Pei S H, Tao Y., New Chemical Materials, 47, 10, (2019)
  • [10] Xu G L, Liang Y, Yang J., polymer Materials Science and Engineering, 28, 8, (2012)
123