Substructure and texture evolution of a novel near-α titanium alloy with bimodal microstructure during hot compression in α plus β phase region

被引:11
作者
Sun, Tao [1 ]
Deng, Yu [1 ]
Liu, Wenhao [2 ]
Teng, Haihao [1 ]
Wang, Ruiqi [1 ,3 ]
Sun, Chaoyuan [1 ,3 ]
Deng, Hao [3 ]
Zhou, Jie [1 ]
机构
[1] Chongqing Univ, Coll Mat Sci & Engn, Chongqing 400044, Peoples R China
[2] Sichuan Univ, Coll Phys, Chengdu 610064, Peoples R China
[3] China Natl Erzhong Grp Co, Deyang Wanhang Die Forging Co Ltd, Deyang 618000, Peoples R China
基金
中国国家自然科学基金;
关键词
Ti65 titanium alloy; Substructure evolution; Deformation texture; Dynamic spheroidization; CRYSTALLOGRAPHIC ORIENTATION EVOLUTION; CHANGING STRAIN-RATE; DEFORMATION-BEHAVIOR; TENSILE DEFORMATION; SLIP TRANSMISSION; WORKING BEHAVIOR; FLOW BEHAVIOR; LAMELLAR; TI-6AL-2ZR-1MO-1V; MECHANISMS;
D O I
10.1016/j.jallcom.2024.174869
中图分类号
O64 [物理化学(理论化学)、化学物理学];
学科分类号
070304 ; 081704 ;
摘要
Ti65 alloy has extensive potential applications in manufacturing high-temperature components in the aerospace industry. During thermomechanical processing in the alpha+beta phase region, complicated microstructure and texture evolution occurs. In this work, isothermal hot compression experiments were conducted to comprehensively investigate the substructure and texture evolution of Ti65 alloy with bimodal microstructure via the electron backscatter diffraction (EBSD) technique, and the influence of processing parameters on the evolution of substructure and texture was systematically analyzed. The experimental results showed that the distribution of grain boundaries and the transformation of low-angle boundaries (LABs) to high-angle boundaries (HABs) exhibited sensitivity to temperature and strain rate. The fraction of sub-grain boundaries decreased, while the fraction of HABs increased with the increasing of strain rate or temperature due to the spheroidization of the lamellar alpha phase accompanied by the wedging of the beta phase during deformation and the relative misorientation angle distribution between different alpha variants precipitated from beta phase. Temperature rising at a high strain rate resulting from adiabatic heat promoted atomic activity, caused dislocations to be absorbed by sub-grain boundaries or HABs, and finally reduced the dislocation density in both alpha(p) and alpha(s) phases. Dynamic spheroidization was the main mechanism with increasing temperature, and coarsening of the lamellar alpha phase was the main mechanism with increasing strain rate. With the increase of temperature or decrease of strain rate, the texture of the alpha(p) phase became stronger and the basal and pyramidal slip could be activated. For the alpha(s) phase, spheroidization and variant selection together influence the orientation distribution. As a result, the texture evolution showed a complicated tendency.
引用
收藏
页数:12
相关论文
共 52 条
[11]   The influence of thermomechanical processing on microstructural evolution of Ti600 titanium alloy [J].
Han, Yuanfei ;
Zeng, Weidong ;
Qi, Yunlian ;
Zhao, Yongqing .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2011, 528 (29-30) :8410-8416
[12]   Tensile deformation behavior of a near-α titanium alloy Ti-6Al-2Zr-1Mo-1V under a wide temperature range [J].
Hao, Fang ;
Xiao, Junfeng ;
Feng, Yong ;
Wang, Yue ;
Ju, Jiantou ;
Du, Yuxuan ;
Wang, Kaixuan ;
Xue, Li'nan ;
Nie, Zhihua ;
Tan, Chengweng .
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2020, 9 (03) :2818-2831
[13]   Effect of retained beta layer on slip transmission in Ti-6Al-2Zr-1Mo-1V near alpha titanium alloy during tensile deformation at room temperature [J].
He, Dong ;
Zhu, Jingchuan ;
Zaefferer, S. ;
Raabe, D. .
MATERIALS & DESIGN, 2014, 56 :937-942
[14]   Processing map-microstructure evolution correlation of hot compressed near alpha titanium alloy (TiHy 600) [J].
Kumar K., Basanth ;
Saxena, Kuldeep K. ;
Dey, Suhash R. ;
Pancholi, Vivek ;
Bhattacharjee, Amit .
JOURNAL OF ALLOYS AND COMPOUNDS, 2017, 691 :906-913
[15]   Research progress on hot deformation behavior of high-strength β titanium alloy: flow behavior and constitutive model [J].
Li, Chang-Min ;
Huang, Liang ;
Li, Cheng-Lin ;
Hui, Song-Xiao ;
Yu, Yang ;
Zhao, Ming-Jie ;
Guo, Shi-Qi ;
Li, Jian-Jun .
RARE METALS, 2022, 41 (05) :1434-1455
[16]   Systematic analysis of the softening mechanism and texture evolution of Ti-6Cr-5Mo-5V-4Al alloy during hot compression in ? plus ? phase region [J].
Li, Changmin ;
Huang, Liang ;
Zhao, Mingjie ;
Guo, Shiqi ;
Su, Yang ;
Li, Jianjun .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2022, 850
[17]   Characterization of hot workability of Ti-6Cr-5Mo-5V-4Al alloy based on hot processing map and microstructure evolution [J].
Li, Changmin ;
Huang, Liang ;
Zhao, Mingjie ;
Guo, Shiqi ;
Su, Yang ;
Li, Jianjun .
JOURNAL OF ALLOYS AND COMPOUNDS, 2022, 905
[18]   Mechanism in the β phase evolution during hot deformation of Ti-5Al-2Sn-2Zr-4Mo-4Cr with a transformed microstructure [J].
Li, L. ;
Li, M. Q. ;
Luo, J. .
ACTA MATERIALIA, 2015, 94 :36-45
[19]   Evolution characterization of α lamellae during isothermal compression of TC17 alloy with colony-α microstructure [J].
Li, Lian ;
Li, Miaoquan .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2018, 712 :637-644
[20]   Variant selection within one β grain in laser solid formed Ti-6Al-4V alloys [J].
Ma, Jiankai ;
Zhang, Yashan ;
Li, Junjie ;
Wang, Zhijun ;
Wang, Jincheng .
MATERIALS CHARACTERIZATION, 2022, 185