The effect of bonding process parameters on the microstructure and mechanical properties of AA5083 diffusion-bonded joints

被引：1

作者：

Venugopal S. ^{[1
]}

Seeman M. ^{[2
]}

Seetharaman R. ^{[3
]}

Jayaseelan V. ^{[4
]}

机构：

[1] Department of Mechanical Engineering, GIET University, Odisha, Gunupur

[2] Department of Manufacturing Engineering, Annamalai University, Annamalai Nagar

[3] Department of Mechanical Engineering, University College of Engineering, Anna University, Dindigul

[4] Department of Mechanical Engineering, Prathyusha Engineering College, Chennai

来源：

International Journal of Lightweight Materials and Manufacture | 2022年 / 5卷 / 04期

关键词：

AA5083; Diffusion bonding; Grain boundary; Pressure; Temperature;

D O I：

10.1016/j.ijlmm.2022.07.003

中图分类号：

学科分类号：

摘要：

Diffusion bonding is a sort of solid-state joining that allows the joining of metals with similar and dissimilar compositions by allowing them to diffuse into one another. The current study investigated the impact of process parameters on the bonding strength of AA5083. The process parameters were considered as bonding temperature, holding time, and bonding pressure. Because of micro-constituent diffusion in the interface, the bonding and shear strengths increased as pressure and temperature were raised in the sample. By increasing the temperature of the Al3Mg2 particles from 490 °C to 520 °C and the bonding pressure from 5 MPa to 15 MPa, the dispersion of secondary phase particles is improved, and pores/defects in bonded joints are reduced. Furthermore, microstructural characterization reveals that the achieved strength is contingent on boundary grain growth and grain boundary migration through the bonding process, respectively. The light optical microscope was used to characterize the microstructural test and diffusion layer configuration at the boundary. © 2022 The Authors

引用

页码：555 / 563

页数：8

共 36 条

[1]

Jayaseelan V., Kalaichelvan K., Seeman M., Ramasamy N., Effect of extrusion ratio and die angle on the microstructure of an AA6063/SiC composite, Mater. Test., 64, 6, pp. 874-883, (2022)

[2]

Venugopal S., Mahendran G., Effect of operation parameters on diffusion bonded AA5083, AA6082 and AA7075 aluminum alloys, Trans. Indian Inst. Met., 71, 9, pp. 185-2198, (2018)

[3]

Du Y., Li Z., Xiong J., Diffusion bonding of FGH 98 and CoCrNi-based medium-entropy alloy: microstructure evolution and mechanical tests, Crystals (Basel), 11, 10, (2021)

[4]

Sunilkumar D., Dey H., Albert S., Shaikh H., Arvinth Davinci M., Murugesan S., Characterization of interfacial microstructure and mechanical properties of the diffusion bonded CP-Ti to AISI 304L stainless steel, Trans. Indian Inst. Met., 74, 1, pp. 9-20, (2020)

[5]

Srimurugan R., Vijay Ananth S., Geethan A., Jayaseelan V., Xavier J.F., Experimental investigation on diffusion bonding of dissimilar metals, AIP Conf. Proc., 2283, 1, (2020)

[6]

Cooke K., Atieh A., Current trends in dissimilar diffusion bonding of titanium alloys to stainless steels, aluminium and magnesium, J. Manuf. Mater. Process., 4, 2, (2020)

[7]

Jie W., Haotian Y., Penghao L., Fuqi Z., Qiaomu L., Qinying W., The microstructure and mechanical properties of YT5 cemented carbide/carbon-carbon composite joints prepared by transient liquid phase diffusion bonding using Ni/Cu/Ti multiple foils as joining materials, Vacuum, 187, (2021)

[8]

Wu F., Chen W., Zhao B., Hou H., Zhou W., Li Z., Diffusion bonding of 1420 Al–Li alloy assisted by pure aluminum foil as interlayer, Materials, 13, 5, (2020)

[9]

Sagai Francis Britto A., Raj R., Mabel M., Prediction of shear and tensile strength of the diffusion bonded AA5083 and AA7075 aluminium alloy using ANN, Mater. Sci. Eng. A, 692, pp. 1-8, (2017)

[10]

Wu F., Zhou W., Zhao B., Hou H., Interface microstructure and bond strength of 1420/7B04 composite sheets prepared by diffusion bonding, Rare Met., 37, 7, pp. 613-620, (2018)

← 1 2 3 4 →