Experimental Study on the Microstructure of FeCoNiCr High-Entropy Alloys by Selective Laser Melting

被引：2

作者：

Wen X.-L. ^{[1
]}

Wang C.-B. ^{[1
]}

Liu W.-B. ^{[1
]}

Ren H.-Y. ^{[2
]}

机构：

[1] School of Mechanical Engineering & Automation, Northeastern University, Shenyang

[2] Air Force Early Warning Academy, Wuhan

来源：

Dongbei Daxue Xuebao/Journal of Northeastern University | 2023年 / 44卷 / 04期

关键词：

defect; high-entropy alloy; microstructure; selective laser melting;

D O I：

10.12068/j.issn.1005-3026.2023.04.011

中图分类号：

学科分类号：

摘要：

The thermal analysis theory of selective laser melting was introduced, and FeCoNiCrAl0.5 and FeCoNiCrAl0.8 high-entropy alloys were prepared by selective laser melting. The effects of powder particle size, element content and process parameters on the microstructure of high-entropy alloys by selective laser melting were analyzed. The results showed that with the increase of laser power, the proportion of equiaxed crystals at the top of the specimen becomes smaller, while the proportion of dendrites in the bottom of the specimen becomes larger and larger. With the increase of scanning speed, the size and width of dendrite in the bottom of high-entropy alloy specimens decrease gradually. The effect of lap ratio on the microstructure of high-entropy alloys is small. It was found that the high-entropy alloy specimens have some defects such as cracks, dents and pores. © 2023 Northeastern University. All rights reserved.

引用

页码：536 / 543

页数：7

共 16 条

[1]

Feng R, Feng B J, Gao M C, Et al., Superior high-temperature strength in a supersaturated refractory high-entropy alloy [J], Advanced Materials, 33, 48, (2021)

[2]

Fan X J, Qu R T, Zhang Z F., Relation between strength and hardness of high-entropy alloys [J], Acta Metallurgica Sinica, 34, 11, pp. 1461-1482, (2021)

[3]

Lv W J, Yang X S, Ji Y Q, Et al., Effects of TiC nanoparticle additions on microstructure and mechanical properties of FeCrAl alloys prepared by directed energy deposition [J], Journal of Nuclear Materials, 554, (2021)

[4]

Zhou K X, Li J J, Wu Q F, Et al., Remelting induced fully-equiaxed microstructures with anomalous eutectics in the additive manufactured Ni32Co30Cr10Fe10Al18 eutectic high-entropy alloy [J], Scripta Materialia, 201, (2021)

[5]

Li X P., Additive manufacturing of advanced multi-component alloys:bulk metallic glasses and high entropy alloys [J], Advanced Engineering Materials, 20, 5, pp. 170-174, (2018)

[6]

Kim Y K, Baek M S, Yang S S, Et al., In-situ formed oxide enables extraordinary high-cycle fatigue resistance in additively manufactured CoCrFeMnNi high-entropy alloy [J], Additive Manufacturing, 38, (2021)

[7]

Fujieda T, Chen M C, Shiratori H, Et al., Mechanical and corrosion properties of CoCrFeNiTi-based high-entropy alloy additive manufactured using selective laser melting [J], Additive Manufacturing, 25, pp. 412-420, (2018)

[8]

Zhang C C, Feng K, Kokawa H, Et al., Cracking mechanism and mechanical properties of selective laser melted CoCrFeMnNi high entropy alloy using different scanning strategies [J], Materials Science and Engineering A, 789, (2020)

[9]

Wang B, Sun M, Li B, Et al., Anisotropic response of CoCrFeMnNi high-entropy alloy fabricated by selective laser melting [J], Materials, 13, 24, pp. 5687-5704, (2020)

[10]

Zhang H, Zhao Y Z, Cai J, Et al., High-strength NbMoTaX refractory high-entropy alloy with low stacking fault energy eutectic phase via laser additive manufacturing [J], Materials &Design, 201, 5, (2021)

← 1 2 →