Microstructure and Mechanical Properties of TC11 Titanium Alloy Fabricated by Wire-feed Electron Beam Additive Manufacturing

被引：1

作者：

Zhang G. ^{[1
]}

Zhang P. ^{[1
]}

Gao J. ^{[1
]}

Yu H. ^{[1
]}

Yuan H. ^{[1
]}

Ding N. ^{[2
]}

Xiong H. ^{[1
]}

机构：

[1] 3D Printing Research and Engineering Technology Center, AECC Beijing Institute of Aeronautical Materials, Beijing

[2] The Sixth Military Representative Office of Airforce in Beijing, Beijing

来源：

Jixie Gongcheng Xuebao/Journal of Mechanical Engineering | 2023年 / 59卷 / 04期

关键词：

additive manufacturing; anisotropy; electron beam; mechanical property; microstructure; titanium alloy;

D O I：

10.3901/JME.2023.04.105

中图分类号：

学科分类号：

摘要：

In this study, a α+β high-temperature titanium alloy TC11 ring (φ260 mm) was fabricated by wire-feed electron beam additive manufacturing (EBAM). The microstructure, tensile property and the anisotropy of the tensile properties of the fabricated alloy were investigated. The microstructure and tensile property of the wrought alloy and the wrought + additive manufacturing interface were also evaluated. Optical microscopy, scanning electron microscopy, transmission electron microscopy and X-ray diffraction were employed to study the microstructure characteristics. The tensile properties along the vertical (V) and horizontal (H) directions were evaluated at both room temperature and 500 ℃. Results indicated that the microstructure of the as-built alloy was characterized by coarse columnar grains, lamellar α (colony and basket-weave), and the continuous grain boundary α. The prior β grains had a strong <001>β texture along the grain growth direction. Compared to the as-built alloy, the lamellar α phase was coarsened from 1.1 μm to 1.8 μm, the discontinuous grain boundary α and bi-lamellar α phase formed by post-deposition heat treated at 950 ℃/2 h/AC+530 ℃/6 h/AC. The equiaxed primary α of the wrought substrate alloy changed from globular to snowflake near the interface. After heat treatment, the volume fraction of the transformed β decreased for the wrought substrate alloy. In terms of tensile properties, the vertical specimens exhibited lower strength but higher ductility than the horizontal specimens at both room and elevated temperatures. The anisotropic elongation results from the directional columnar prior β grains and continuous grain boundary α phase, which facilitated the intergranular cracking. The tensile strength and ductility were simultaneously enhanced by the heat treatment to meet the standard requirements for wrought counterparts. Moreover, the anisotropy of the tensile strength and elongation for the post-deposition heat treated alloy was decreased significantly from 4.4% and 27.1% to 1.6% and 5.4%, respectively, in comparison to the as-built alloy. The tensile property of the wrought+additive manufacturing interface can meet the standard requirements for wrought counterparts. © 2023 Editorial Office of Chinese Journal of Mechanical Engineering. All rights reserved.

引用

页码：105 / 112

页数：7

共 31 条

[1]

CHEN Huiqin, CAO Chunxiao, GUO Ling, Et al., Hot deformation globularization kinetic processes of TC11 titanium alloy with lamellar structure[J], Journal of Aeronautical Materials, 29, 1, pp. 37-42, (2009)

[2]

LI Minna, Chen WU, MA Baofei, Et al., Research on distribution regularity of microstructure and properties of large-sized TC11 titanium alloy bar after heat treatment[J], Titanium Industry Progress, 39, 1, pp. 12-15, (2022)

[3]

Wei LIU, LI Neng, ZHOU Biao, Et al., Progress in additive manufacturing on complex structures and high-performance materials[J], Journal of Mechanical Engineering, 55, 20, pp. 128-151, (2019)

[4]

OLIVEIRA J P, SANTOS T G, MIRANDA R M., Revisiting fundamental welding concepts to improve additive manufacturing ： From theory to practice[J], Progress in Materials Science, 107, (2020)

[5]

Neng LI, HUANG Shuai, ZHANG Guodong, Et al., Progress in additive manufacturing on new materials：A review[J], Journal of Materials Science & Technology, 35, pp. 242-269, (2019)

[6]

QIN Renyao, ZHANG Guodong, LI Neng, Et al., Research progress on additive manufacturing of TiAl-based alloys[J], Journal of Mechanical Engineering, 57, 8, pp. 115-132, (2021)

[7]

HUANG Shuai, SUN Bingbing, Shaoqing GUO, Microstructure and property evaluation of TA15 titanium alloy fabricated by selective laser melting after heat treatment[J], Optics & Laser Technology, 144, (2021)

[8]

REN Haishui, TIAN Xiangjun, LIU Dong, Et al., Microstructural evolution and mechanical properties of laser melting deposited Ti-6.5Al-3.5Mo-1.5Zr-0.3Si titanium alloy[J], Transactions of Nonferrous Metals Society of China, 25, pp. 1856-1864, (2015)

[9]

ZHU Yanyan, TIAN Xiangjun, LI Jia, Et al., The anisotropy of laser melting deposition additive manufacturing Ti-6.5Al-3.5Mo-1.5Zr-0.3Si titanium alloy[J], Materials and Design, 67, pp. 538-542, (2015)

[10]

WANG T, ZHU Y Y, ZHANG S Q, Et al., Grain morphology evolution behavior of titanium alloy components during laser melting deposition additive manufacturing[J], Journal of Alloys and Compounds, 632, pp. 505-513, (2015)

← 1 2 3 4 →