Effect of Intake Conditions and Nozzle Geometry on Spray Characteristics of Group-Hole Nozzle

被引：0

作者：

Pan J. ^{[1
]}

Hua J. ^{[1
]}

Yao J. ^{[1
]}

Ojo A.O. ^{[1
]}

机构：

[1] School of Energy and Power Engineering, Jiangsu University, Zhenjiang

来源：

Energy Engineering: Journal of the Association of Energy Engineering | 2023年 / 120卷 / 07期

基金：

中国国家自然科学基金;

关键词：

coupling model; Diesel; group-hole nozzle; spray characteristics;

D O I：

10.32604/ee.2023.027873

中图分类号：

学科分类号：

摘要：

The group-hole nozzle concept is proposed to meet the requirement of nozzle hole minimization and reduce the negative impact of poor spatial spray distributions. However, there are limited researches on the effects of intake conditions and nozzle geometry on spray characteristics of the group-hole nozzle. Therefore, in this study, an accurate spray model coupled with the internal cavitating flow was established and computational fluid dynamics (CFD) simulations were done to study the effects of intake conditions and nozzle geometry on spray characteristics of the group-hole nozzle. Experimental data obtained using high-speed digital camera on the high-pressure common rail injection system was used to validate the numerical model. Effects of intake conditions (injection pressure and temperature) and nozzle geometry (orifice entrance curvature radius and nozzle length) on the flow and spray characteristics of the group-hole nozzle were studied numerically. The differences in Sauter mean diameter (SMD), penetration length and fuel evaporation mass between single-hole nozzle and group-hole nozzle under different nozzle geometry were also discussed. It was found that the atomization performance of the group-hole nozzle was better than that of the single-hole nozzle under same intake conditions, and the atomization effect of the short nozzle was better than that of the long nozzle. With increase in the orifice entrance curvature radius, the average velocity and turbulent kinetic energy of the fuel increased, which was conducive to improving the injection rate and flow coefficient of the nozzle. Meanwhile, the penetration length and SMD value rose, while evaporation mass dropped. When the ratio of the orifice entrance curvature radius (R) to the diameter of injection hole (D) was 0.12, the spray characteristics reached a constant state due to elimination of cavitation. Conclusions were made based on these. This study is expected to be a guide for the design of the group-hole nozzle. © 2023, Tech Science Press. All rights reserved.

引用

页码：1541 / 1562

页数：21

共 39 条

[1]

Behcet R., Aydin H., Ilkilic C., Iscan B., Aydin S., Diesel engine applications for evaluation of performance and emission behavior of biodiesel from different oil stocks, Environmental Progress & Sustainable Energy, 34, 3, pp. 890-896, (2014)

[2]

Karabas H., Boran S., Comparison of engine performance and exhaust emission properties of diesel and saff lower biodiesel using multi-response surface methodology, Environmental Progress & Sustainable Energy, 38, 4, (2018)

[3]

Gumus M., Sayin C., Canakci M., The impact of fuel injection pressure on the exhaust emissions of a direct injection diesel engine fueled with biodiesel-diesel fuel blends, Fuel, 95, pp. 86-494, (2012)

[4]

He L., Ruiz F., Effect of cavitation on f low and turbulence in plain orifices for high-speed atomization, Atomization and Sprays, 5, 6, pp. 569-584, (1995)

[5]

Kushari A., Effect of injector geometry on the performance of an internally mixed liquid atomizer, Fuel Processing Technology, 9, 11, pp. 1650-1654, (2010)

[6]

Soteriou C., Andrews R., Smith M., Direct injection diesel sprays and the effect of cavitation and hydraulic f lip on atomization, SAE International Journal of Engines, 104, pp. 128-153, (1995)

[7]

Ganippa L. C., Bark G., Andersson S., Chomiak J., Cavitation: A contributory factor in the transition from symmetric to asymmetric jets in crossf low nozzles, Experiments in Fluids, 36, 4, pp. 627-634, (2004)

[8]

Bergwerk W., Flow pattern in diesel nozzle spray holes, Proceedings of the Institution of Mechanical Engineers, 173, 1, pp. 655-660, (1959)

[9]

Hiroyasu H., Arai M., Structures of fuel sprays in diesel engines, SAE International Journal of Engine, 99, pp. 1050-1061, (1990)

[10]

Soteriou C., Andrews R., Smith M., Further studies of cavitation and atomization in diesel injection, SAE International Journal of Engine, 108, pp. 902-919, (1999)

← 1 2 3 4 →