Self-calibration optimization method for laser tracking multilateral measurement

被引：0
作者：
Li X. [1 ,2 ]
Lin H. [2 ]
Xue Z. [2 ]
Yang G. [2 ]
机构：
[1] College of Precision Instrument and Opto-Electronics Engineering, Tianjin University, Tianjin
[2] National Institute of Metrology, Beijing
来源：
Yi Qi Yi Biao Xue Bao/Chinese Journal of Scientific Instrument | 2021年 / 42卷 / 02期
关键词：
Laser tracking measurement; Multilateral method; Self-calibration optimization;
D O I：
10.19650/j.cnki.cjsi.J2007108
中图分类号：
学科分类号：
摘要：
During the measurement of large space objects with the laser tracking multilateral method, the measurement accuracy is affected by a lot of factors. The accuracy of the self-calibration is one of key factors. In this paper, a self-calibration optimization method is proposed. Through introducing the cross spatial distribution model of the points for the optimized calibration, the data of the laser base stations obtained from the initial self-calibration are calibrated once again, and the optimization algorithm is used to get the more accurate data of the laser base stations, so as to reduce the error in the self-calibration process and improve the accuracy of laser tracking multilateral measurement. The distance measurement experiment on a groups of space points in the x-axis direction was carried out, the optimization effect of the data of base stations was verified through introducing calibration points. The experiment results indicate that the distances of the measured points obtained based on the data of the base stations after the optimized calibration are closer to the reference distances, and the distance difference is reduced from -2.3 μm to -1.6 μm after optimization at the position with the x-axis coordinate of 750 mm. So, the self-calibration optimization method proposed in this paper could improve the accuracy of the laser tracking multilateral measurements. © 2021, Science Press. All right reserved.
引用
收藏
页码：10 / 17
页数：7
相关论文
共 19 条
  • [1] MIAO D J, SUN W, LI J SH, Et al., Influence of the number of measurement stations on the measurement accuracy of multilateral coordinate measurement system, Chinese Journal of Scientific Instrument, 41, 7, pp. 38-44, (2020)
  • [2] LI M, YU J P., Status and development of geometric measurement in Industry, Chinese Journal of Scientific Instrument, 38, 12, pp. 2959-2971, (2017)
  • [3] GAO F, GE Y S, WANG T, Et al., Vision-based localization model based on spatial plane constraints, Chinese Journal of Scientific Instrument, 39, 7, pp. 183-190, (2018)
  • [4] YU K, CONG M Y, DAI W C., Spatial target vision pose measurement based on 3D model, Chinese Journal of Scientific Instrument, 40, 4, pp. 179-188, (2019)
  • [5] WANG X J, GAO J, WANG L., Survey on the laser triangulation, Chinese Journal of Scientific Instrument, 25, Z3, pp. 601-604, (2004)
  • [6] LUO Z, LIU H, TIAN K, Et al., Error analysis and compensation of the measuring force of the articulated arm coordinate measuring machine, Chinese Journal of Scientific Instrument, 38, 5, pp. 1159-1167, (2017)
  • [7] WENDT K, FRANKE M, HAERTIG F., Measuring large 3D structures using four portable tracking laser interferometers, Measurement, 25, pp. 2239-2345, (2012)
  • [8] SUN Y Y, DONG M L, QIAO Y J., Operation modal analysis of large wind turbine blades based on photogrammetry, Journal of Electronic Measurement and Instrumentation, 33, 10, pp. 165-172, (2019)
  • [9] WU B, XU Y, YANG F T, Et al., 3D coordinate measuring system based on laser tracking absolute length measurement multilateral method, Infrared and Laser Engineering, 47, 8, pp. 140-145, (2018)
  • [10] ZHANG L G, XIONG ZH, FENG W, Et al., Laser tracking attitude angle measurement method based on vision and laser collimation, Chinese Journal of Scientific Instrument, 41, 8, pp. 30-36, (2020)
12