Elastic and damping characterization of open-pore metal foams filled or not with an elastomer for vibration control in turbomachinery

被引:0
|
作者
Lacaj, Endri [1 ]
Jolly, Pascal [1 ]
Bouyer, Jean [1 ]
Doumalin, Pascal [1 ]
机构
[1] Univ Poitiers, Inst Pprime, UPR CNRS 3346, ISAE ENSMA, F-86360 Chasseneuil, France
关键词
Metal-foam / elastomer composites; bearings; vibration damping; turbomachinery; INTERPENETRATING PHASE COMPOSITES; BEHAVIOR;
D O I
10.1051/meca/2024021
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
In this work, an experimental investigation into vibration damping of elastomer filled open-pore metal foams and their effectiveness as a bearing support in turbomachinery is presented. The polyurethane fillers known for their high-energy absorption capacity were chosen to enhance the damping performance of the metal skeleton. Aluminum (Al), copper (Cu) and nickel-chromium foams (NiCr), with different relative density and pore size were tested dynamically using a dedicated device based on a single degree-of-freedom model. The results indicate that the storage modulus and the loss factor for foam-polymer composites were greater than the combined contribution of both phases taken separately. Foam morphology plays an important role in this effect and it is shown that the increase in performance was more significant for higher specific surface area. Fillers with different properties were also considered. The optimal combination of foam and polymer was selected and tested on a rotor kit test bench. Annular shaped samples were placed between the external race of the ball bearing and the housing. The tests were carried out using a flexible rotor configuration where the vibration amplitudes of the rotor were monitored for foam and foam-polyurethane composites for rotational speeds up to 100 Hz while hammer impact tests were performed using a semi-rigid shaft configuration due to higher resonance frequencies. In the first case, no significant difference was observed between the foam, foam composite and the bearings-only set-up. In the second case, the foam composite resulted with the highest energy dissipation capacity.
引用
收藏
页数:11
相关论文
共 14 条
  • [1] ELASTIC AND DAMPING CHARACTERIZATION OF OPEN-PORE METAL FOAMS FILLED OR NOT WITH AN ELASTOMER FOR VIBRATION CONTROL IN TURBOMACHINERY
    Lacaj, Endri
    Jolly, Pascal
    Bouyer, Jean
    Doumalin, Pascal
    PROCEEDINGS OF ASME TURBO EXPO 2023: TURBOMACHINERY TECHNICAL CONFERENCE AND EXPOSITION, GT2023, VOL 11A, 2023,
  • [2] Microstructural Characterization of Open-Pore Metal Foams of Pure Metals
    Mocker, B. S.
    Matz, A. M.
    Jost, N.
    Krug, P.
    PRAKTISCHE METALLOGRAPHIE-PRACTICAL METALLOGRAPHY, 2015, 52 (02): : 83 - 107
  • [3] Mesostructural Design and Manufacturing of Open-Pore Metal Foams by Investment Casting
    Matz, Alexander Martin
    Mocker, Bettina Stefanie
    Mueller, Daniel Wyn
    Jost, Norbert
    Eggeler, Gunther
    ADVANCES IN MATERIALS SCIENCE AND ENGINEERING, 2014, 2014
  • [4] Effective thermal conductivity of open-pore metal foams as a function of the base material
    Matz, Alexander Martin
    Mocker, Bettina Stefanie
    Jost, Norbert
    Krug, Peter
    MATERIALS TESTING, 2015, 57 (10) : 825 - 836
  • [5] Structure-property correlation of open-pore metal foams using 3D structural characterization
    Grote, F
    Busse, P
    Schmitz, M
    MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK, 2000, 31 (06) : 470 - 473
  • [6] Fabrication, characterization and electrochemical response of pitch-derived open-pore carbon foams as electrodes
    Iniesta, Jesús (jesus.iniesta@ua.es), 1600, Springer Science and Business Media B.V. (48):
  • [7] Fabrication, characterization and electrochemical response of pitch-derived open-pore carbon foams as electrodes
    Hernandez-Ibanez, Naiara
    Montiel, Vicente
    Miguel Molina-Jorda, Jose
    Iniesta, Jesus
    JOURNAL OF APPLIED ELECTROCHEMISTRY, 2018, 48 (03) : 329 - 342
  • [8] Fabrication, characterization and electrochemical response of pitch-derived open-pore carbon foams as electrodes
    Naiara Hernández-Ibáñez
    Vicente Montiel
    José Miguel Molina-Jordá
    Jesús Iniesta
    Journal of Applied Electrochemistry, 2018, 48 : 329 - 342
  • [9] Some Aspects of the Optimisation of Open-pore Metal Foams by Introducing Bio-inspired Hierarchical Levels
    Fischer, S. F.
    Schueler, P.
    Bayerlein, B.
    Fleck, C.
    Buehrig-Polaczek, A.
    POROUS METALS AND METALLIC FOAMS, METFOAM 2011, 2012, : 57 - 62
  • [10] Analysis and 3D-Modelling of Open-Pore Metal Foams Using Binarized Light-Optical Microscopy In-Depth Microsections
    Matz, Alexander M.
    Jost, Norbert
    PRAKTISCHE METALLOGRAPHIE-PRACTICAL METALLOGRAPHY, 2012, 49 (11): : 664 - 681