Improvement of Tribological Properties and Corrosion Resistance of AISI 4340M Steel by Shot Peening and Plating Technologies

被引:0
|
作者
Ahn, Seok-Hwan [1 ]
Kim, Jungsik [2 ]
Amanov, Auezhan [3 ]
机构
[1] Jungwon Univ, Dept Unmanned Aero Mech Engn, Goesan 28024, South Korea
[2] Jungwon Univ, Grad Sch, Dept Convergence Engn, Goesan 28024, South Korea
[3] Tampere Univ, Fac Engn & Nat Sci, Tampere 33700, Finland
关键词
AISI; 4340M; shot peening; heat treatment; Cr-plating; stripping; tribology; corrosion resistance; SURFACE; STRENGTH; BEHAVIOR;
D O I
10.3390/met14091037
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
In this study, shot peening (SP), quenching and tempering (QT) heat treatment, baking heat treatment and Cr-plating technologies were used to enhance the hardness, tribological properties and corrosion resistance of AISI 4340M steel. The purpose of this study is to develop repair process technology for an overhaul of landing gear applied to the MRO process and establish a quality assurance system. The effects of SP, QT heat treatment, Cr-plating, stripping after Cr-plating and Cr-plating after stripping and re-SP on the tribological properties and corrosion resistance of AISI 4340M steel were investigated, and the obtained results were compared with the base AISI 4340M steel. One of the reasons for stripping after Cr-plating is to find out how many times stripping can be done after Cr-plating. Moreover, it is important to investigate the effect of re-SP after Cr-plating on the tribological properties and corrosion resistance. The tribological properties of the specimens were investigated using a ball-on-disk tribometer at room temperature against AISI 52100 steel for 60 min under dry conditions. The corrosion resistance was investigated using a potentiodynamic polarization test in NaCl 3.5% solution. The results showed that the application of SP, QT heat treatment, Cr-plating, stripping after Cr-plating and Cr-plating after stripping and re-SP had a significant effect on the tribological properties and corrosion resistance of AISI 4340M steel. The effects of SP and Cr-plating post-treatment technologies on the wear and corrosion enhancement and mechanisms were discussed based on the microstructural and surface morphology of worn and corroded surfaces.
引用
收藏
页数:17
相关论文
共 50 条
  • [31] Effect of shot peening and treatment temperature on wear and corrosion resistance of sequentially plasma treated AISI 316L steel
    Menezes, Marcela Rabelo
    Godoy, Cristina
    Buono, V. T. L.
    Schvartzman, Monica M. M.
    Wilson, J. C. Avelar-Batista
    SURFACE & COATINGS TECHNOLOGY, 2017, 309 : 651 - 662
  • [32] Influence of Shot Peening on Residual Stress Distribution and Corrosion Resistance of Additive Manufactured Stainless Steel AISI 316L
    A. Vinoth Jebaraj
    M. Sugavaneswaran
    Transactions of the Indian Institute of Metals, 2019, 72 : 1651 - 1653
  • [33] CORROSION RESISTANCE OF AISI 316Ti STAINLESS STEEL SUBJECTED TO SHOT PEENING WITH AND WITHOUT PICKLING IN VARIOUS CHLORIDE ENVIRONMENTS
    Liptakova, Tatiana
    Alaskari, Ayman
    Trsko, Libor
    Dundekova, Sylvia
    TRANSACTIONS OF FAMENA, 2017, 41 (03) : 81 - 90
  • [34] Influence of Shot Peening on Residual Stress Distribution and Corrosion Resistance of Additive Manufactured Stainless Steel AISI 316L
    Jebaraj, A. Vinoth
    Sugavaneswaran, M.
    TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, 2019, 72 (06) : 1651 - 1653
  • [35] Effect of Shot Peening Parameters on Surface Properties and Corrosion Resistance of 316L Stainless Steel
    Walczak, Mariusz
    Matijosius, Jonas
    Ozkan, Dogus
    Pasierbiewicz, Kamil
    ADVANCES IN SCIENCE AND TECHNOLOGY-RESEARCH JOURNAL, 2024, 18 (03) : 296 - 304
  • [36] Effect of Shot Peening on the Corrosion and Wear Resistance of 2205 Duplex Stainless Steel
    Yi Wu
    Yonghai Kang
    Youming Chen
    Journal of Materials Engineering and Performance, 2023, 32 : 3186 - 3201
  • [37] Effect of Shot Peening on the Corrosion and Wear Resistance of 2205 Duplex Stainless Steel
    Wu, Yi
    Kang, Yonghai
    Chen, Youming
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2023, 32 (07) : 3186 - 3201
  • [38] Mechanical properties and corrosion resistance of nanocrystalline ZrNxOy coatings on AISI 304 stainless steel by ion plating
    Huang, Jia-Hong
    Tsai, Zhang-En
    Yu, Ge-Ping
    SURFACE & COATINGS TECHNOLOGY, 2008, 202 (20): : 4992 - 5000
  • [39] Effects of shot peening pressure, media type and double shot peening on the microstructure, mechanical and tribological properties of low-alloy steel
    Pham Quang Trung
    Khun, Nay Win
    Butler, David Lee
    SURFACE TOPOGRAPHY-METROLOGY AND PROPERTIES, 2016, 4 (04):
  • [40] Evaluation of pre-shot peening on improvement of carburizing heat treatment of AISI 9310 gear steel
    Wu, Jizhan
    Wei, Peitang
    Liu, Huaiju
    Zhang, Xiuhua
    He, Zhiqiang
    Deng, Guanyu
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2022, 18 : 2784 - 2796