Numerical simulation research on multiphase flow of aviation centrifugal pump based on OpenFOAM

被引:4
|
作者
Liu, Xianwei [1 ,2 ]
Fu, Jiangfeng [1 ]
Yang, Junjie [3 ]
Yin, Dewen [3 ]
Zhou, Zhenhua [4 ]
Li, Huacong [1 ]
机构
[1] Northwestern Polytech Univ, Coll Power & Energy, Xian 710072, Peoples R China
[2] Norinco Grp Testing & Res Inst, Huayin 714200, Peoples R China
[3] AECC Xian Engine Control Technol Co Ltd, Xian 710077, Peoples R China
[4] AECC Guizhou Honglin Aero Engine Control Technol C, Guiyang 550009, Peoples R China
基金
中国国家自然科学基金;
关键词
Aero engine; Fuel centrifugal pump; Multiphase flow; Volume of fluid; OpenFOAM; FLUX-CORRECTED TRANSPORT; CAVITATION;
D O I
10.1016/j.cja.2023.11.016
中图分类号
V [航空、航天];
学科分类号
08 ; 0825 ;
摘要
This paper aims to tackle the calculation efficiency problem raised in the cavitation-flow simulation of the aviation centrifugal pump due to the fading-away interface resulting from the dissipation of numerics used in the phase-change control equation for unstructured-grid multiphase flow, and due to the limitation of flow time-step in whole flow regimes, the control equation of vapor-liquid two-phase flow considering cavitation mass transport is established firstly, modifying the momentum equation by introducing the surface tension, and adding the artificial convective flow to the phase equation to solve the numerical dissipation problem. Secondly, in consideration of the local time step principle and based on the multi-dimensional general limiter algorithm with explicit solutions under the OpenFOAM platform, a solution method of steady-state VOF (Volume of Fluid) model considering cavitation two-phase change is constructed, and the feasibility of this method is verified by NACA hydrofoil and NASA flat plate inducer. Finally, based on the platform developed, the cavitation performance of an aviation centrifugal pump inducer is analyzed. The research results show that the error of the calculated cavitation pressure distribution for NACA hydrofoil between the simulation test and the experimental-test is less than 5%, and the maximum error of calculated cavitation number at pump head dropping for NASA high-speed flat plate inducer between the simulation test and the experimental-test is 2.1%. The cavitation area observed in the simulation test is the same as that obtained in the high-speed photography test. Based on the OpenFOAM simulation method, the position of pump head dropping of the fuel centrifugal pump can be accurately captured. The error of the calculated cavitation number at pump head dropping between the simulation test and the experimental test is about 3.7%, showing high calculation accuracy. (c) 2023 Production and hosting by Elsevier Ltd. on behalf of Chinese Society of Aeronautics and Astronautics. This is an open access article under the CC BY -NC -ND license (http://creativecommons.org/ licenses/by-nc-nd/4.0/).
引用
收藏
页码:256 / 275
页数:20
相关论文
共 50 条
  • [31] Numerical simulation for the inner flow field of aero fuel centrifugal pump
    Li, Jia
    Li, Huacong
    Fu, Jiangfeng
    Wang, Shuhong
    Xibei Gongye Daxue Xuebao/Journal of Northwestern Polytechnical University, 2015, 33 (02): : 278 - 283
  • [32] Numerical simulation on internal flow of centrifugal pump during transient operation
    Wu, Da-Zhuan
    Xu, Bin-Jie
    Li, Zhi-Feng
    Wang, Le-Qin
    Kung Cheng Je Wu Li Hsueh Pao/Journal of Engineering Thermophysics, 2009, 30 (05): : 781 - 783
  • [33] Numerical simulation of flow in centrifugal pump under cavitation and sediment condition
    Guo, P. C.
    Lu, J. L.
    Zheng, X. B.
    Zhao, Q.
    Luo, X. Q.
    26TH IAHR SYMPOSIUM ON HYDRAULIC MACHINERY AND SYSTEMS, PTS 1-7, 2013, 15
  • [34] Numerical Simulation of the Transient Flow in a Centrifugal Pump During Starting Period
    Li, Zhifeng
    Wu, Dazhuan
    Wang, Leqin
    Huang, Bin
    JOURNAL OF FLUIDS ENGINEERING-TRANSACTIONS OF THE ASME, 2010, 132 (08):
  • [35] Numerical Simulation of Internal Flow in Stamping and Welding Multistage Centrifugal Pump
    Liu, Yuanyi
    Li, Ruiguang
    Sun, Kai
    MATERIALS PROCESSING TECHNOLOGY, PTS 1-4, 2011, 291-294 : 2608 - 2611
  • [36] Numerical simulation and analysis of flow characteristics in the front chamber of a centrifugal pump
    Yang Wu
    Xiaoping Chen
    Hua-Shu Dou
    Lulu Zheng
    Zuchao Zhu
    Baoling Cui
    Boo Cheong Khoo
    Journal of Mechanical Science and Technology, 2017, 31 : 5131 - 5140
  • [37] Numerical simulation and analysis of flow characteristics in the front chamber of a centrifugal pump
    Wu, Yang
    Chen, Xiaoping
    Dou, Hua-Shu
    Zheng, Lulu
    Zhu, Zuchao
    Cui, Baoling
    Khoo, Boo Cheong
    JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY, 2017, 31 (11) : 5131 - 5140
  • [38] Numerical Simulation Research on Radial Force of Centrifugal Pump with Guide Vanes
    Meng, Dongrong
    Jiang, Ting
    Deng, Hongling
    Hou, Gaoyang
    SHOCK AND VIBRATION, 2021, 2021 (2021)
  • [39] Numerical Simulation Research on Vortex Characteristics of Centrifugal Pump Inlet Recirculation
    Yuan, Jianping
    Sun, Wei
    Wang, Longyan
    Liang, Yun
    AUTOMATION EQUIPMENT AND SYSTEMS, PTS 1-4, 2012, 468-471 : 2235 - 2240
  • [40] Research on the Performance of a Centrifugal Aviation Fuel Pump Based on Response Surface Methodology
    Zhou, Jianbo
    He, Dongjing
    Zhang, Rui
    Zhao, Weidong
    PROCESSES, 2023, 11 (11)