Numerical simulation research on multiphase flow of aviation centrifugal pump based on OpenFOAM

被引:4
|
作者
Liu, Xianwei [1 ,2 ]
Fu, Jiangfeng [1 ]
Yang, Junjie [3 ]
Yin, Dewen [3 ]
Zhou, Zhenhua [4 ]
Li, Huacong [1 ]
机构
[1] Northwestern Polytech Univ, Coll Power & Energy, Xian 710072, Peoples R China
[2] Norinco Grp Testing & Res Inst, Huayin 714200, Peoples R China
[3] AECC Xian Engine Control Technol Co Ltd, Xian 710077, Peoples R China
[4] AECC Guizhou Honglin Aero Engine Control Technol C, Guiyang 550009, Peoples R China
基金
中国国家自然科学基金;
关键词
Aero engine; Fuel centrifugal pump; Multiphase flow; Volume of fluid; OpenFOAM; FLUX-CORRECTED TRANSPORT; CAVITATION;
D O I
10.1016/j.cja.2023.11.016
中图分类号
V [航空、航天];
学科分类号
08 ; 0825 ;
摘要
This paper aims to tackle the calculation efficiency problem raised in the cavitation-flow simulation of the aviation centrifugal pump due to the fading-away interface resulting from the dissipation of numerics used in the phase-change control equation for unstructured-grid multiphase flow, and due to the limitation of flow time-step in whole flow regimes, the control equation of vapor-liquid two-phase flow considering cavitation mass transport is established firstly, modifying the momentum equation by introducing the surface tension, and adding the artificial convective flow to the phase equation to solve the numerical dissipation problem. Secondly, in consideration of the local time step principle and based on the multi-dimensional general limiter algorithm with explicit solutions under the OpenFOAM platform, a solution method of steady-state VOF (Volume of Fluid) model considering cavitation two-phase change is constructed, and the feasibility of this method is verified by NACA hydrofoil and NASA flat plate inducer. Finally, based on the platform developed, the cavitation performance of an aviation centrifugal pump inducer is analyzed. The research results show that the error of the calculated cavitation pressure distribution for NACA hydrofoil between the simulation test and the experimental-test is less than 5%, and the maximum error of calculated cavitation number at pump head dropping for NASA high-speed flat plate inducer between the simulation test and the experimental-test is 2.1%. The cavitation area observed in the simulation test is the same as that obtained in the high-speed photography test. Based on the OpenFOAM simulation method, the position of pump head dropping of the fuel centrifugal pump can be accurately captured. The error of the calculated cavitation number at pump head dropping between the simulation test and the experimental test is about 3.7%, showing high calculation accuracy. (c) 2023 Production and hosting by Elsevier Ltd. on behalf of Chinese Society of Aeronautics and Astronautics. This is an open access article under the CC BY -NC -ND license (http://creativecommons.org/ licenses/by-nc-nd/4.0/).
引用
收藏
页码:256 / 275
页数:20
相关论文
共 50 条
  • [21] Three-Dimensional Numerical Flow Simulation in a Centrifugal Pump
    Chalghoum, Issa
    Elaoud, Sami
    Akrout, Mohsen
    Taieb, Ezzeddine Hadj
    Design and Modeling of Mechanical Systems - II, 2015, : 801 - 809
  • [22] RESEARCH OF INNER FLOW IN A DOUBLE BLADES PUMP BASED ON OPENFOAM
    LIU Hou-lin
    Journal of Hydrodynamics, 2012, 24 (02) : 226 - 234
  • [23] RESEARCH OF INNER FLOW IN A DOUBLE BLADES PUMP BASED ON OPENFOAM
    Liu Hou-lin
    Ren Yun
    Wang Kai
    Wu Deng-hao
    Ru Wei-min
    Tan Ming-gao
    JOURNAL OF HYDRODYNAMICS, 2012, 24 (02) : 226 - 234
  • [24] Research of Inner Flow in a Double Blades Pump Based on Openfoam
    Hou-lin Liu
    Yun Ren
    Kai Wang
    Deng-hao Wu
    Wei-min Ru
    Ming-gao Tan
    Journal of Hydrodynamics, 2012, 24 : 226 - 234
  • [25] Numerical Simulation of Subcooled Flow Boiling Based on OpenFOAM Platform
    Qin H.
    Wang M.
    Li L.
    Tian W.
    Su G.
    Qiu S.
    Yuanzineng Kexue Jishu/Atomic Energy Science and Technology, 2019, 53 (11): : 2157 - 2161
  • [26] NUMERICAL SIMULATION OF MULTIPHASE FLOW IN VENTILATION MILL AND CHANNEL WITH LOUVERS AND CENTRIFUGAL SEPARATOR
    Kozic, Mirko S.
    Ristic, Slavica S.
    Puharic, Mirjana A.
    Katavic, Boris T.
    THERMAL SCIENCE, 2011, 15 (03): : 677 - 689
  • [27] NUMERICAL SIMULATION AND PIV MEASUREMENT ON THE INTERNAL FLOW IN A CENTRIFUGAL MINI PUMP
    Shao, Jie
    Liu, Shuhong
    Yuan, Huijing
    Wu, Yuliun
    PROCEEDINGS OF THE ASME FLUIDS ENGINEERING DIVISION SUMMER CONFERENCE -2008, VOL 1, PT A AND B, 2009, : 1107 - 1113
  • [28] Numerical simulation and experiment study for turbulent flow in the impeller of centrifugal pump
    Yang, Minguan
    Gu, Haifei
    Liu, Dong
    Jia, Weidong
    Gao, Bo
    Jixie Gongcheng Xuebao/Chinese Journal of Mechanical Engineering, 2006, 42 (12): : 180 - 185
  • [29] Numerical Simulation of the Transient Flow in a Centrifugal Pump during Regulating Period
    Tang, Yue
    Liu, Erhui
    Tang, Lingdi
    Hui, Wang
    COMPUTATIONAL MATERIALS SCIENCE, PTS 1-3, 2011, 268-270 : 1407 - +
  • [30] Numerical simulation and analysis of unsteady flow characteristics in centrifugal pump volute
    Meng, Genqiqige
    Tan, Lei
    Cao, Shuliang
    Wang, Yuchuan
    Jixie Gongcheng Xuebao/Journal of Mechanical Engineering, 2015, 51 (22): : 183 - 190