Numerical simulation research on multiphase flow of aviation centrifugal pump based on OpenFOAM

被引:4
|
作者
Liu, Xianwei [1 ,2 ]
Fu, Jiangfeng [1 ]
Yang, Junjie [3 ]
Yin, Dewen [3 ]
Zhou, Zhenhua [4 ]
Li, Huacong [1 ]
机构
[1] Northwestern Polytech Univ, Coll Power & Energy, Xian 710072, Peoples R China
[2] Norinco Grp Testing & Res Inst, Huayin 714200, Peoples R China
[3] AECC Xian Engine Control Technol Co Ltd, Xian 710077, Peoples R China
[4] AECC Guizhou Honglin Aero Engine Control Technol C, Guiyang 550009, Peoples R China
基金
中国国家自然科学基金;
关键词
Aero engine; Fuel centrifugal pump; Multiphase flow; Volume of fluid; OpenFOAM; FLUX-CORRECTED TRANSPORT; CAVITATION;
D O I
10.1016/j.cja.2023.11.016
中图分类号
V [航空、航天];
学科分类号
08 ; 0825 ;
摘要
This paper aims to tackle the calculation efficiency problem raised in the cavitation-flow simulation of the aviation centrifugal pump due to the fading-away interface resulting from the dissipation of numerics used in the phase-change control equation for unstructured-grid multiphase flow, and due to the limitation of flow time-step in whole flow regimes, the control equation of vapor-liquid two-phase flow considering cavitation mass transport is established firstly, modifying the momentum equation by introducing the surface tension, and adding the artificial convective flow to the phase equation to solve the numerical dissipation problem. Secondly, in consideration of the local time step principle and based on the multi-dimensional general limiter algorithm with explicit solutions under the OpenFOAM platform, a solution method of steady-state VOF (Volume of Fluid) model considering cavitation two-phase change is constructed, and the feasibility of this method is verified by NACA hydrofoil and NASA flat plate inducer. Finally, based on the platform developed, the cavitation performance of an aviation centrifugal pump inducer is analyzed. The research results show that the error of the calculated cavitation pressure distribution for NACA hydrofoil between the simulation test and the experimental-test is less than 5%, and the maximum error of calculated cavitation number at pump head dropping for NASA high-speed flat plate inducer between the simulation test and the experimental-test is 2.1%. The cavitation area observed in the simulation test is the same as that obtained in the high-speed photography test. Based on the OpenFOAM simulation method, the position of pump head dropping of the fuel centrifugal pump can be accurately captured. The error of the calculated cavitation number at pump head dropping between the simulation test and the experimental test is about 3.7%, showing high calculation accuracy. (c) 2023 Production and hosting by Elsevier Ltd. on behalf of Chinese Society of Aeronautics and Astronautics. This is an open access article under the CC BY -NC -ND license (http://creativecommons.org/ licenses/by-nc-nd/4.0/).
引用
收藏
页码:256 / 275
页数:20
相关论文
共 50 条
  • [1] Numerical simulation research on multiphase flow of aviation centrifugal pump based on OpenFOAM
    Xianwei LIU
    Jiangfeng FU
    Junjie YANG
    Dewen YIN
    Zhenhua ZHOU
    Huacong LI
    Chinese Journal of Aeronautics , 2024, (04) : 256 - 275
  • [2] Numerical simulation of the inner flow in a centrifugal pump with OpenFOAM
    Ren, Yun
    Liu, Houlin
    Wu, Denghao
    Tan, Minggao
    Shu, Minhua
    Yingyong Jichu yu Gongcheng Kexue Xuebao/Journal of Basic Science and Engineering, 2012, 20 (06): : 1042 - 1050
  • [3] Numerical Simulation and Performance Prediction of Centrifugal Pump's Full Flow Field Based on OpenFOAM
    Huang, Si
    Wei, Yifeng
    Guo, Chenguang
    Kang, Wenming
    PROCESSES, 2019, 7 (09)
  • [4] Numerical simulation and experiment on gas-liquid-solid multiphase flow in centrifugal pump
    Research Center of Fluid Machinery Engineering and Technology, Jiangsu University, Zhenjiang 212013, China
    Wang, X. (jsuwxl@163.com), 1600, Chinese Society of Agricultural Engineering (28):
  • [5] Numerical Simulation of Cavitation Flow in a Centrifugal Pump
    Zhao, Weiguo
    He, Xiaoxia
    Wang, Xiuyong
    Li, Yibin
    ADVANCES IN COMPUTATIONAL MODELING AND SIMULATION, PTS 1 AND 2, 2014, 444-445 : 509 - 516
  • [6] Flow Numerical Simulation of Centrifugal Pump with Splitting Blades based on RE
    Ren Neifei
    Chen Mingmin
    Jiang Jie
    Cheng Li
    ADVANCES IN MECHATRONICS TECHNOLOGY, 2011, 43 : 691 - +
  • [7] Numerical Investigation on Multiphase Flow Simulation in a Centrifugal Flotation Cell
    Ghaffari, Ali
    Karimi, Mohsen
    INTERNATIONAL JOURNAL OF COAL PREPARATION AND UTILIZATION, 2012, 32 (03) : 120 - 129
  • [8] Numerical Simulation of Flow in Centrifugal Pump with Complex Impeller
    Cui, Bao-ling
    Lin, Yong-gang
    Jin, Ying-zi
    JOURNAL OF THERMAL SCIENCE, 2011, 20 (01) : 47 - 52
  • [9] Numerical simulation and experiments on the flow in a multistage centrifugal pump
    Benra, FK
    Feng, JJ
    Proceedings of the Sixth International Conference on Fluid Power Transmission and Control, 2005, : 430 - 434
  • [10] Numerical simulation of flow in centrifugal pump with complex impeller
    Bao-ling Cui
    Yong-gang Lin
    Ying-zi Jin
    Journal of Thermal Science, 2011, 20 : 47 - 52