Continuous DLP ceramic 3D printing

被引：0

作者：

Wang H. ^{[1
]}

Lan H. ^{[1
]}

Qian L. ^{[1
]}

Zhao J. ^{[1
]}

Xu Q. ^{[1
]}

Zhu X. ^{[1
]}

Zhang G. ^{[1
]}

Lu Z. ^{[2
]}

Li D. ^{[2
]}

机构：

[1] Qingdao Engineering Research Center for 3D Printing, Qingdao Technological University, Qingdao

[2] State Key Laboratory for Manufacturing System Engineering, Xi'an Jiaotong University, Xi'an

来源：

Zhongguo Kexue Jishu Kexue/Scientia Sinica Technologica | 2019年 / 49卷 / 06期

关键词：

Additive manufacturing; Ceramic 3D printing; Ceramic slurry; Continuous 3D printing; Oxygen-rich composite film;

D O I：

10.1360/N092018-00338

中图分类号：

学科分类号：

摘要：

In order to resolve the problems of the low efficiency and the anisotropy of printed object in the traditional ceramic 3D printing techniques, a novel continuous digital light processing (DLP) ceramic 3D printing implemented by utilizing the combination of an oxygen-rich composite thin film and the resin-based ceramics slurry has been proposed and developed. The basic principle and the process flow of the proposed continuous ceramic 3D printing are described. Then, the ceramic slurry used for this proposed 3D printing technique is investigated and optimized, and the effects and the rules of primary process parameters on forming process are revealed by conducting a series of experiments. Finally, two typical cases are provided to demonstrate the feasibility and validity of the proposed process. As a result, a continuous DLP ceramic 3D printing has been fulfilled, which provides a promising and novel solution for high-efficiency, low-cost ceramic 3D printing. © 2019, Science Press. All right reserved.

引用

页码：681 / 689

页数：8

共 11 条

[1] Eckel Z.C., Zhou C., Martin J.H., Et al., Additive manufacturing of polymer-derived ceramics, Science, 351, pp. 58-62, (2016)
[2] Hwa L.C., Rajoo S., Noor A.M., Et al., Recent advances in 3D printing of porous ceramics: A review, Curr Opin Solid State Mater Sci, 21, pp. 323-347, (2017)
[3] Gualtieri T., Bandyopadhyay A., Additive manufacturing of compositionally gradient metal-ceramic structures: Stainless steel to vanadium carbide, Mater Design, 139, pp. 419-428, (2018)
[4] Chartier T., Dupas C., Lasgorceix M., Et al., Additive manufacturing to produce complex 3D ceramic parts, J Ceram Sci Technol, 6, pp. 95-104, (2014)
[5] Costa E., Duarte J.P., Bartolo P., A review of additive manufacturing for ceramic production, Rapid Prototyping J, 23, pp. 954-963, (2017)
[6] Yun J.S., Park T.W., Jeong Y.H., Et al., Development of ceramic-reinforced photopolymers for SLA 3D printing technology, Appl Phys A, 122, (2016)
[7] Deckers J., Vleugels J., Kruth J.P., Additive manufacturing of ceramics: A review, J Ceram Sci Technol, 5, pp. 245-260, (2014)
[8] Scheithauer U., Slawik T., Schwarzer E., Et al., Additive manufacturing of metal-ceramic-composites by thermoplastic 3D-printing (3DTP), J Ceram Sci Technol, 6, pp. 125-131, (2015)
[9] Huang B., Bartolo P.J., Rheological characterization of polymer/ceramic blends for 3D printing of bone scaffolds, Polymer Testing, 68, pp. 365-378, (2018)
[10] Scheithauer U., Schwarzer E., Moritz T., Et al., Additive manufacturing of ceramic heat exchanger: Opportunities and limits of the lithography-based ceramic manufacturing (LCM), J Materi Eng Perform, 27, pp. 14-20, (2018)

← 1 2 →