Pose estimation method for a simultaneous three-fingered end-effector

被引:0
作者
Fan S. [1 ]
Wu J. [1 ]
Jin M. [1 ]
Fan C. [1 ]
Liu H. [1 ]
机构
[1] State Key Laboratory of Robotics and System, Harbin Institute of Technology, Harbin
来源
Harbin Gongcheng Daxue Xuebao/Journal of Harbin Engineering University | 2019年 / 40卷 / 02期
关键词
Contact force information; Dock and capture; End-effector; Least squares method; Pose estimation; Simultaneous three-fingered;
D O I
10.11990/jheu.201705043
中图分类号
学科分类号
摘要
To determine the target pose in the process of end-effector capturing, this study develops a pose estimation method for a simultaneous three-fingered end effector based on contact force information. The pose estimation method is proposed after analyzing the geometric constraint characteristics of the end effector. First, the contact finger is estimated with the contact force. Then, the contact position and normal direction are estimated by combining the kinematic analysis results of the end effector. The spatial plane intersection method is adopted for pose estimation with two effective contact information. When obtaining redundant contact information, the least squares method is adopted to update the estimation results. Finally, simulation validates the effectiveness of the estimation method. The proposed method has general applicability to a certain extent and specific applicability to claw-shaped end effectors. © 2019, Editorial Department of Journal of HEU. All right reserved.
引用
收藏
页码:359 / 364
页数:5
相关论文
共 18 条
  • [1] Lyu X., Xia Y., Liu R., Design of an under-actuated self-adaptive capture device, Journal of Harbin Engineering University, 37, 12, pp. 1709-1715, (2016)
  • [2] Feng F., Liu Y., Liu H., Et al., Design schemes and comparison research of the end-effector of large space manipulator, Chinese Journal of Mechanical Engineering, 25, 4, pp. 674-687, (2012)
  • [3] Ciocarlie M., Hicks F.M., Holmberg R., Et al., The velo gripper: A versatile single-actuator design for enveloping, parallel and fingertip grasps, The International Journal of Robotics Research, 33, 5, pp. 753-767, (2014)
  • [4] Font D., Pallej T., Tresanchez M., Et al., A proposal for automatic fruit harvesting by combining a low cost stereovision camera and a robotic arm, Sensors, 14, 7, pp. 11557-11579, (2014)
  • [5] Mehta S.S., Burks T.F., Vision-based control of robotic manipulator for citrus harvesting, Computers and Electronics in Agriculture, 102, pp. 146-158, (2014)
  • [6] Xu W., Liang B., Li C., Et al., Measurement and planning approach of space robot for capturing non-cooperative target, Robot, 32, 1, pp. 61-69, (2010)
  • [7] Hu J., Guan Y., Wu P., Et al., Pole pose measurement and autonomous grasping with a biped climbing robot, Robot, 36, 5, pp. 569-575, (2014)
  • [8] Zhang Y., Sun K., Liu H., Et al., Pose measurement of nozzle based on laser range finders for capturing satellite, Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering, 230, 8, pp. 1385-1396, (2016)
  • [9] Zhang Y., Sun K., Zhang Y., Et al., Design of a laser range finder for end perception of robot arm, Robot, 36, 5, (2014)
  • [10] Tsujimura T., Yabuta T., Object detection by tactile sensing method employing force/torque information, IEEE Transactions on Robotics and Automation, 5, 4, pp. 444-450, (1989)