Effect of friction stir processing on mechanical properties of AA-TIG welded 9%Ni steel

被引：0

作者：

Mori M. ^{[1
]}

Tokuda T. ^{[2
,3
]}

Morisada Y. ^{[4
]}

Fujii H. ^{[4
]}

机构：

[1] Faculty of Advanced Science and Technology, Ryukoku University

[2] Graduate School of Science and Technology, Ryukoku University

[3] Joining and Welding Research Institute, Osaka University

来源：

Yosetsu Gakkai Ronbunshu/Quarterly Journal of the Japan Welding Society | 2021年 / 39卷 / 03期

关键词：

9%Ni steel; AA-TIG welding; FSP; Micro-impact test; Pining effect; Toughness;

D O I：

10.2207/QJJWS.39.200

中图分类号：

学科分类号：

摘要：

Active-TIG (A-TIG) or Advanced Active-TIG (AA-TIG) welding is an effective method to improve the welding penetration depth by introducing of active elements such as oxygen into the weld metal. However, increasing oxygen content in the weld metal decreases the toughness of the weld metal. Grain refinement is regarded as one of the most effective ways to improve the toughness of materials. Friction stir processing (FSP) is suitable for reducing grain size in small area such as the weld metal. This study elucidates the effect of FSP on the toughness of 9%Ni steel weld metal containing different oxygen contents. The 9%Ni steel weld metal were fabricated via AA-TIG welding using a mixed gas of Ar and O2. The oxygen contents in the weld metal were 180, 250, and 330 ppm. FSP treated the weld metal formed via AA-TIG welding. The microstructures of the weld metal and stir zone were observed using the optical microscope (OM), scanning electron microscope (SEM), and electron backscatter diffraction (EBSD). The micro-impact test was conducted to measure the toughness of the weld metal and stir zone. Although the toughness of the weld metal decreased with increasing oxygen content in the weld zone, FSP could improve it regardless of the oxygen content in the stir zone. In particular, the toughness of the stir zone with oxygen content of 330 ppm was considerably increased, and it reached almost the same value as the base metal. These improvements depend on the grain refinement in the stir zone. The smallest grain size of former austenite was obtained in the stir zone with an oxygen content of 330 ppm because numerous small inclusion particles lead to clear pining effect. © 2021 Japan Welding Society. All rights reserved.

引用

页码：200 / 208

页数：8

共 28 条

[1]

Tanaka M., Shimizu T., Terasaki T., Ushio M., Koshi-ishi F., Yang C.-L., Effects of Activating Flux on Arc Phenomena in Gas Tungsten Arc Welding, Science and Technology of Welding and Joining, 5-6, pp. 397-402, (2000)

[2]

Howse D.S., Lucas W., Investigation into Arc Constriction by Active Fluxes for Tungsten Inert Gas Welding, Science and Technology of Welding and Joining, 5-3, pp. 189-193, (2000)

[3]

Lu S., Fujii H., Sugiyama H., Tanaka M., Nogi K., Weld Penetration and Marangoni Convection with Oxide Fluxes in GTA Welding, Materials Transactions, 43-11, pp. 2926-2931, (2002)

[4]

Lu S., Fujii H., Sugiyama H., Tanaka M., Nogi K., Effects of Oxygen Additions to Argon Shielding Gas on GTA Weld Shape, ISIJ International, 43-10, pp. 1590-1595, (2003)

[5]

Fujii H., Sato T., Lu S.P., Nogi K., Development of Advanced A-TIG (AA-TIG) Welding Method by Control of Marangoni Convection, Materials Science and Engineering A, 495, pp. 296-303, (2008)

[6]

Lu S., Fujii H., Nogi K., Marangoni Convection and Weld Shape Variations in Ar-O<sub>2</sub> and Ar-CO<sub>2</sub> Shielded GTA Welding, Materials Science and Engineering A, 380, pp. 290-297, (2004)

[7]

Morisada Y., Fujii H., Xukun N., Development of Simplified Active Flux Tungsten Inert Gas Welding for Deep Penetration, Materials & Design, 54, pp. 526-530, (2014)

[8]

Zou Y., Ueji R., Fujii H., Mechanical Properties of Advanced Active-TIG Welded Duplex Stainless Steel and Ferrite Steel, Materials Science and Engineering A, 620, pp. 140-148, (2015)

[9]

Tsuji N., Saito Y., Lee S.-H., Minamoto Y., ARB (Accumulative Roll-Bonding) and other New Techniques to Produce Bulk Ultrafine Grained Materials, Advanced Engineering Materials, 5-5, pp. 338-344, (2003)

[10]

Saito Y., Utsunomiya H., Tsuji N., Sakai T., Novel Ultra-High Straining Process for Bulk Materials-Development of the Accumulative Roll-Bonding (ARB) Process, Acta Materialia, 47-2, pp. 579-583, (1999)

← 1 2 3 →