Experimental study on mechanical anisotropy of irregular columnar jointed rock mass under conventional triaxial compression condition

被引：0

作者：

Xiao W. ^{[1
,2
]}

Han J. ^{[1
,2
]}

Tian M. ^{[1
,2
]}

Wu Z. ^{[1
,2
]}

机构：

[1] School of Civil Engineering, Sichuan Agricultural University, Sichuan, Dujiangyan

[2] Sichuan Higher Education Engineering Research Center for Disaster Prevention and Mitigation of Village Construction, Sichuan Agricultural University, Sichuan, Dujiangyan

来源：

Yanshilixue Yu Gongcheng Xuebao/Chinese Journal of Rock Mechanics and Engineering | 2023年 / 42卷

基金：

中国国家自然科学基金;

关键词：

columnar joints; conventional triaxial compression test; mechanical anisotropy; rock mass; rock mechanics;

D O I：

10.13722/j.cnki.jrme.2022.0272

中图分类号：

学科分类号：

摘要：

Based on 3D printing and physical model test method，artificial irregular columnar jointed rock mass specimens with seven different dip angles were prepared by one-shot moulding method where brittle green wax was chosen as 3D printing material to print irregular columnar joint network in which white cement slurry was poured. Conventional triaxial compression tests were performed on these artificial irregular columnar jointed rock mass specimens，from which their strength and deformation anisotropy and typical failure modes were derived. From the experimental results，it showed that the strength，deformation modulus and lateral strain ratio of irregular columnar jointed rock mass exhibited moderate or high anisotropy and confining pressure had significant effect on its mechanical anisotropy. Furthermore，the typical failure modes of irregular columnar jointed rock mass under conventional compression condition had been classified into four kinds，that was，Y-shaped conjugate shear failure along columnar joints，splitting failure along both intact column and columnar joint，shear slip failure along columnar joint and axial splitting of intact columns. Finally，the influence of 3D printed green wax irregular columnar joint network on mechanical behaviors of irregular columnar jointed rock mass was analyzed. © 2023 Academia Sinica. All rights reserved.

引用

页码：3131 / 3140

页数：9

共 25 条

[1]

XU Songnian, Research on volcanic rock columnar joint structure, (1995)

[2]

QUE X C，, ZHU Z D, LU W B., Anisotropic constitutive model of pentagonal prism columnar jointed rock mass[J], Bulletin of Engineering Geology and the Environment, 79, 1, pp. 269-286, (2020)

[3]

LU Yiran, Deformation anisotropy study of columnar jointed rock masses, (2010)

[4]

ZHANG Yihu, ZHOU Huoming, ZHONG Zuowu, Et al., In situ rock masses triaxial test system YXSW–12 and its application[J], Chinese Journal of Rock Mechanics and Engineering, 30, 11, pp. 2312-2320, (2011)

[5]

JIANG Quan, FENG Xiating, FAN Yilin, Et al., Survey and laboratory study of anisotropic properties for columnar jointed basaltic rock mass[J], Chinese Journal of Rock Mechanics and Engineering, 32, 12, pp. 2527-2535, (2013)

[6]

NING Yu, XU Weiya, ZHENG Wentang, Et al., Study of random simulation of columnar jointed rock mass and its representative elementary volume scale[J], Chinese Journal of Rock Mechanics and Engineering, 27, 6, pp. 1202-1208, (2008)

[7]

ZHU Daojian, YANG Linde, CAI Yongchang, Research on anisotropic characteristics and size effect of columnar jointed rock mass[J], Chinese Journal of Rock Mechanics and Engineering, 28, 7, pp. 1405-1414, (2009)

[8]

YAN L, WANG R B, Et al., Numerical simulation of the anisotropic properties of a columnar jointed rock mass under triaxial compression[J], Engineering Computations, 35, 4, pp. 1788-1804, (2018)

[9]

MENG Q X, WANG H L, XU W Y., Numerical homogenization study on the effects of columnar jointed structure on the mechanical properties of rock mass[J], International Journal of Rock Mechanics and Mining Sciences, 124, (2019)

[10]

LIU Haining, WANG Junmei, WANG Sijing, Experimental research of columnar jointed basalt with true triaxial apparatus at Baihetan Hydropower Station[J], Rock and Soil Mechanics, 31, pp. 163-171, (2010)

← 1 2 3 →