Preparation and hot compression deformation of biomedical Ni-Ti alloy

被引：0
|
作者：
Wang Z. [1 ]
Xu X.-W. [1 ]
Wang K.-S. [2 ]
Wang W. [2 ]
机构：
[1] Department of Biomedical Engineering, Central South University, Changsha
[2] School of Metallurgy Engineering, Xi'an University of Architecture and Technology, Xi'an
来源：
Gongcheng Kexue Xuebao/Chinese Journal of Engineering | 2019年 / 41卷 / 02期
关键词：
Hot compression; Hot processing map; Ni-Ti alloy; Strain curves;
D O I：
10.13374/j.issn2095-9389.2019.02.011
中图分类号：
学科分类号：
摘要：
A Ti-50.7%Ni (atomic fraction) shape alloy was prepared by vacuum induction melting under dynamic argon atmosphere. By analyzing the composition, deformation temperature, microstructure, and hardness of the as-cast Ni-Ti shape alloy in this study, it was found that the properties of the as-cast Ni-Ti alloy met the medical standard. To analyze the variation law of the flow stress, the flow stress of the compression deformation for as-cast Ni-Ti alloy was studied by high-temperature compression with a Gleeble-3800 simulated machine within a deformation temperature range of 750-950℃, strain rate range of 0.001-1.0 s-1, and strain level of 0.5. To analyze the relationship between variables in the hot deformation process of as-cast Ni-Ti alloy, a constitutive equation based on dynamic material model was established. To determine the reasonable range of hot working conditions for as-cast Ni-Ti alloy deformation, hot processing maps under different hot deformation conditions were set up. The results show that when the deformation temperature decreases or strain rate increases, the flow stress of as-cast Ni-Ti alloy increases. This phenomenon shows that the main factors affecting the flow stress of as-cast Ni-Ti alloy are deformation temperature and strain rate. When the strain rate is 1.0 s-1, the true stress-true strain curves of as-cast Ni-Ti alloy exhibits a zigzag feature. This is mainly attributed to the alternation between hardening and softening during deformation. According to the hot processing maps under different hot deformation conditions, the processing zone and unstable hot deformation region of the as-cast Ni-Ti alloy were obtained. Then, the best temperature range of hot deformation is determined as 820-880℃, and the true strain rate is less than 0.1 s-1. This study provides a theoretical and data basis for the development of forging process parameters of Ni-Ti alloy. © All right reserved.
引用
收藏
页码：238 / 245
页数：7
相关论文
共 24 条
  • [1] Jani J.M., Leary M., Subic A., Et al., A review of shape memory alloy research, applications and opportunities, Mater Des, 56, (2014)
  • [2] Frenzel J., George E.P., Dlouhy A., Et al., Influence of Ni on martensitic phase transformations in NiTi shape memory alloys, Acta Mater, 58, 9, (2010)
  • [3] Jiang S.Y., Zhang Y.Q., Microstructure evolution and deformation behavior of as-cast NiTi shape memory alloy under compression, Trans Nonferrous Met Soc China, 22, 1, (2012)
  • [4] Zhao W.B., Material characteristic and medical application of nickel-titanium shape memory alloy, J Clin Rehabilitative Tissue Eng Res, 11, 22, (2007)
  • [5] Niinomi M., Recent metallic materials for biomedical application, Metall Mater Trans A, 33, 3, (2002)
  • [6] Zhang Y.T., Liu H.Y., Wang C., Et al., Development trend and research application situation of biomedical metal materials, Hot Working Technol, 46, 4, (2017)
  • [7] Gao Y.J., Chen H.N., Shape memory alloy and its application in medicine, Guangxi Phys, 22, 1, (2001)
  • [8] Yu Z.T., Yu S., Cheng J., Et al., Development and application of novel biomedical titanium alloy materials, Acta Metall Sinica, 53, 10, (2017)
  • [9] Lei W.G., Zhao Y.Q., Han D., Et al., Development of melting technology for titanium alloys, Mater Rev, 30, 3, (2016)
  • [10] Chen W., Zhang W.H., Liu L.H., Et al., Status and trend in the development of the research on the processing technic for NiTi SMA, Forging Stamping Technol, (2005)
123