Effect of shielding gas composition on gas metal arc welding phenomena using rare earth metal added wire

被引:0
作者
Tanaka M. [1 ]
Methong T. [2 ]
Komen H. [3 ]
Shigeta M. [1 ]
Kataoka T. [4 ]
Matsushita M. [5 ]
Kozuki S. [5 ]
机构
[1] Joining and Welding Research Institute, Osaka University
[2] King Mongkut's University of Technology, Thonburi
[3] Magnesium Research Center, Kumamoto University
来源
Yosetsu Gakkai Ronbunshu/Quarterly Journal of the Japan Welding Society | 2021年 / 38卷 / 04期
关键词
Gas metal arc welding; Imaging spectroscopy; Metal transfer; Polarity; Rare earth metal;
D O I
10.2207/QJJWS.38.438
中图分类号
学科分类号
摘要
In this study, to clarify effects of the rare earth metal (REM) on arc phenomena, observations of an arc appearance and a metal transfer during a gas metal arc welding using a REM added wire by a high-speed camera were conducted. Moreover, temperature measurements of the arc plasma were carried out using monochromators and high-speed cameras. As a result, the spray transfer mode was observed during the welding with the electrode negative polarity using the REM added wire when the shielding gas including CO2 gas was used. The globular transfer mode was obtained during the welding when 100%Ar gas was used as a shielding gas. These results showed the reverse tendency compared with a conventional gas metal arc welding using the electrode positive polarity. Moreover, the droplet frequency increased largely in the range of 220A to 260A during the gas metal arc welding with the electrode negative polarity using the REM added wire when the shielding gas including CO2 gas was used. From these results, it was suggested that the spray transfer mode during CO2 gas arc welding and metal active gas welding was obtained by two factors. One was the operation and stabilization of the hot cathode by the welding with the electrode negative polarity using the REM added wire, and the other was the increase of temperature of the molten metal droplet and constriction of arc and arc root by the thermal pinch effect. © 2020 Japan Welding Society. All rights reserved.
引用
收藏
页码:438 / 447
页数:9
相关论文
共 21 条
  • [1] (2016)
  • [2] Lancaster J. F., The Physics of Welding, (1986)
  • [3] Matsuda F., Ushio M., Nishikawa H., Yokoo T., Pulsed GMAW: Spattering in Pulsed CO2 Welding, Transactions of JWRI, 14-1, pp. 13-19, (1985)
  • [4] (1996)
  • [5] Kataoka T., Ikeda R., Sakaguchi S., Yasuda K., Tokinori K., Development of Low Spatter CO2 Arc Welding Using High Frequency Pulse Current, Materia Japan, 43, 2, pp. 151-153, (2004)
  • [6] Yamazaki K., Suzuki R., Shimizu H., Koshiishi F., Spatter and fume reduction in CO2 gas-shielded arc welding by regulated globular transfer, Welding in the World, 56-9-10, pp. 12-19, (2012)
  • [7] Sato E., Yamazaki K., Regulated Globular Transfer Method for CO2 Gas Shielded Arc Welding, Journal of the Japan Welding Society, 84, 4, pp. 239-243, (2015)
  • [8] Kataoka T., Ikeda R., Sakaguchi S., Yasuda K., Influence of Minor Elements in Electrode Wire on Spattering Phenomena in CO2 Gas Shielded Arc Welding, Quarterly Journal of the Japan Welding Society, 25-3, pp. 410-415, (2007)
  • [9] Kataoka T., Ikeda R., Ono M., Yasuda K., Hirata Y., Effect of REM Addition of Wire on CO2 Gas Shielded Arc Phenomenon, Quarterly Journal of the Japan Welding Society, 26-1, pp. 37-41, (2008)
  • [10] Methong T., Yamaguchi T., Shigeta M., Tanaka M., Ikeda R., Matsushita M., Poopat B., Effect of rare earth metal on plasma properties in GMAW using CO2 shielding gas, Welding in the World, 61-5, pp. 1039-1047, (2017)