Optimization of process parameters and performances of cryogenic cutting of magnesium alloy

被引：0

作者：

Fan L. ^{[1
]}

Yan P. ^{[1
]}

Chen S. ^{[1
]}

Chen H. ^{[1
]}

Jiao L. ^{[1
]}

Qiu T. ^{[1
]}

Wang X. ^{[1
]}

机构：

[1] School of Mechanical Engineering, Beijing Institute of Technology, Beijing

来源：

Harbin Gongye Daxue Xuebao/Journal of Harbin Institute of Technology | 2022年 / 54卷 / 07期

关键词：

Cryogenic cutting; Grey relational analysis; Parameter optimization; Residual stress; Surface integrity; ZK61M magnesium alloy;

D O I：

10.11918/202112060

中图分类号：

学科分类号：

摘要：

To improve the machinability and surface integrity of magnesium alloys, and optimize the machining parameters, a set of orthogonal experiment with four factors and four levels were carried out based on the method of pseudo-level. Comparative study involved in the influence of three different cooling strategies, namely, dry cutting, liquid carbon and liquid nitrogen coolants, as well as the cutting parameters on the surface integrity of ZK61M magnesium alloy during turning were conducted. The experimental results show that the effect of cutting depth on cutting force is the most significant factor, the feed quantity is the second significant factor, the effect of cutting speed on cutting force is ignorable. Although the effect of cryogenic cutting on cutting force is not significant, it can reduce the cutting force in some extents. The feed rate has a significant effect on the surface roughness and surface residual stress. As the feed rate increasing, the surface roughness increases and the residual stress is introduced on the machined surface. The cooling medium has a sub-significant effect on the surface roughness and surface residual stress. Compared with dry turning, The cryogenic coolants can effectively reduce the surface roughness, refine the surface grain and increase the surface compressive residual stress during cutting. As a cooling medium, the liquid carbon dioxide is more effective than liquid nitrogen in improving the machining-induced surface integrity. Grey relational analysis is used to obtain the optimal process parameters for cryogenic cutting of ZK61M magnesium alloy: vc= 100 m/min, f= 0.05 mm/r, ap= 0.4 mm, liquid carbon dioxide is used as the cooling medium. The response prediction model between the process parameters and the machined surface quality was established through the results of the relational analysis, the average error was 7.93%. Copyright ©2022 Journal of Harbin Institute of Technology.All rights reserved.

引用

页码：53 / 63and69

页数：6316

共 28 条

[1]

ZENG Xiaoqin, WANG Qudong, LV Yizhen, Et al., New development of magnesium alloy application, Casting, 11, (1998)

[2]

LI Shan, WANG Bojian, Research, development and application of wrought magnesium alloys, Hot Working Technology, 36, (2007)

[3]

DIEM W., Magnesium in different applications, Auto Technology, 1, 1, (2001)

[4]

WANG Jiadi, CHENG Yu, LU Chen, Et al., Discussion about cutting of the magnesium alloys, Machine Design and Manufacturing Engineering, 31, 3, (2002)

[5]

QI Jin, Research on surface integrity of low temperature cooling turning magnesium alloy AZ31B, (2019)

[6]

PU Z, OUTEIRO J C, BATISTA A C, Et al., Surface integrity in dry and cryogenic machining of AZ31B Mg alloy with varying cutting edge radius tools, Procedia Engineering, 19, (2011)

[7]

PU Z, OUTEIRO J C, BATISTA A C, Et al., Enhanced surface integrity of AZ31B Mg alloy by cryogenic machining towards improved functional performance of machined components, International Journal of Machine Tools and Manufacture, 56, (2012)

[8]

CHAABANI S, ARRAZOLA P J, AYED Y, Et al., Surface integrity when machining inconel 718 using conventional lubrication and carbon dioxide coolant, Procedia Manufacturing, 47, (2020)

[9]

VIGNESH S, IQBAL U M., Experimental investigation on machining parameters of Hastelloy C276 under different cryogenic environment, Advances in Forming, Machining and Automation, (2019)

[10]

HOU Peng, Selection of cutting parameters for magnesium alloy machining, Science & Technology Information, 24, (2010)

← 1 2 3 →