Study on wear resistance of 20Cr2Ni4A steel surface WC reinforced iron-based coating

被引：0

作者：

Liu J.-G. ^{[1
]}

Zheng W.-J. ^{[1
]}

Wang G.-S. ^{[1
]}

He L.-H. ^{[2
]}

Zhao Y.-H. ^{[1
]}

机构：

[1] School of Mechanical Engineering, Xiangtan University, Xiangtan

[2] Hunan Institute of Engineering, Xiangtan

来源：

Surface Technology | 2021年 / 50卷 / 06期

基金：

中国国家自然科学基金;

关键词：

20Cr2Ni4A; Laser cladding; Microhardness; Wear extent; Wear resistant coating;

D O I：

10.16490/j.cnki.issn.1001-3660.2021.06.026

中图分类号：

学科分类号：

摘要：

To prepare excellent wear-resistant coatings for the surface of mechanical parts, which can effectively increase their service life and reduce various failures caused by mechanical equipment wear. Using 20Cr2Ni4A alloy steel as the matrix material, the iron-based coating and the iron-based/WC composite coating were prepared by laser cladding technology. By using X-ray diffraction (XRD), metallurgical microscope and scanning electron microscope (SEM), HV-1000 micro Vickers hardness tester, the phase composition, structure, morphology and microhardness of iron-based coating and iron-based/WC composite coating are characterized respectively; HRS-2M high-speed reciprocating friction and wear tester was used to study the wear resistance of iron-based coatings and iron-based/WC composite coatings, and analyze their wear mechanisms. The microhardness of the two coatings was improved more than that of the substrate. Among them, the iron-based/WC composite coating was improved the most, with an average surface hardness of 610HV. Taking GCr15 with a diameter of 6 mm as the friction pair, the average friction coefficient of the iron-based coating is about 0.53 and the wear amount is 0.1432 mm3, while the average friction coefficient of the iron-based/WC composite coating is only about 0.36, and the wear amount is only 0.059 35 mm3. Compared with the iron-based coating, the hardness of the 20Cr2Ni4A alloy steel surface combined with the iron-based/WC composite coating is increased by about 17%, and the amount of wear is reduced by 58.6%, which shows good wear resistance. W2C, WC, Fe3C and other phases, which are evenly distributed on the iron-based coating as a wear-resistant framework, can significantly improve the hardness of the coating and wear resistance. © 2021, Chongqing Wujiu Periodicals Press. All rights reserved.

引用

页码：236 / 242

页数：6

共 22 条

[1]

Xu Q.-G., Study on laser cladding layer of iron-based alloy reinforced by ceramic particles[D], (2012)

[2]

Lin N., Wu C.H., He Y.H., Et al., Effect of Mo and Co additions on the microstructure and properties of WC-TiC-Ni cemented carbides[J], International journal of refractory metals & hard materials, 30, 1, pp. 107-113, (2012)

[3]

Li L., Zhang G.Z., Fu Z.Y., Et al., Wear mechanisms analysis of material 20Cr2Ni4A[J], Advanced materials research, 85, pp. 13-16, (2013)

[4]

Zhang W., A brief discussion on wear failure and protective measures of metal materials[J], Scientific and technological innovation, 18, pp. 23-24, (2020)

[5]

Bauyrzhan K.R., Vladimir V.B., Zarina A., Et al., The cathodic electrolytic plasma hardening of the 20Cr2Ni4A chromium-nickel steel[J], Journal of materials research and technology, 9, 4, (2020)

[6]

Li G.-L., Li C.-Y., Xing Z.-G., Et al., Study of the catalytic strengthening of a vacuum carburized layer on alloy steel by rare earth pre-implantation.[J], Materials, 12, 20, (2019)

[7]

Yue C.-W., Study on surface shot peening strengthening of carburized gear steel[D], (2018)

[8]

Zhang Y.-F., Xu X.-J., Wu F.-C., A composite brush plating repairing technology for 20Cr2Ni4A steel surface carbrized layer[J], Surface technology, 39, 3, pp. 100-102, (2010)

[9]

Zhao W.-J., Liu G.-Q., Cai H., Et al., Research on rare earth carburized process of 20Cr2Ni4A gear steel[J], Casting, 67, 9, pp. 831-835, (2018)

[10]

Yin C., Zhang P., Zhao J.-J., Effect of ultrasonic wave impact on properties of 20Cr2Ni4A carburized gear steel[J], Journal of academy of armored force engineering, 30, 4, pp. 88-90, (2016)

← 1 2 3 →