Cooling performance analysis of combustion liner in reverse-flow combustor

被引:0
作者
Li W. [1 ]
Yang L. [1 ]
机构
[1] College of Mechanical and Vehicle Engineering, Hunan University, Changsha
来源
Hangkong Xuebao/Acta Aeronautica et Astronautica Sinica | 2023年 / 44卷 / 09期
关键词
combustion; cooling hole; cooling performance; failure; reverse-flow combustor; vortex pair;
D O I
10.7527/S1000-6893.2022.27326
中图分类号
学科分类号
摘要
To study the combustion and cooling performance of the combustion liner in the reverse-flow combustor,a combustor model was built,and failure reasons were analyzed through heat fluid-structure coupling simulation. By introducing film cooling holes with different hole types and dip angles,the cooling effect of the original defective compo⁃ nent part was compared. The results show that the location of the maximum temperature and maximum temperature gradient of the original structural part is the same as the failure location of the actual fault part,so that it can be consid⁃ ered that the failure is caused by high temperature and high temperature gradient;compared with initial cooling struc⁃ ture,the maximum temperature of the inner wall of the reverse combustor all decreased after the hole structure change,281. 34 K at most and 60. 15 K at least;with the same hole type,the cooling effectiveness is the best at a hole inclination angle of 30°,and the cooling effectiveness is the worst at the hole inclination angle of 60°. With the same hole inclination angle,the cooling effectiveness of the convergent hole is the best,because of a vortex pair op⁃ posite to the original structure generated on the section near the outlet end,therefore improving the cooling effect,while the cooling effectiveness of cylindrical holes is the worst. © 2023 AAAS Press of Chinese Society of Aeronautics and Astronautics. All rights reserved.
引用
收藏
相关论文
共 25 条
[11]  
KREWINKEL R., A review of gas turbine effusion cool⁃ ing studies[J], International Journal of Heat and Mass Transfer, 66, pp. 706-722, (2013)
[12]  
NIU J J, LIU C L, LIU H Y,, Et al., Effects of area ratio of film hole to impingement hole and momentum flux ra⁃ tio on overall cooling effectiveness of afterburner double wall heat shield[J], Journal of Propulsion Technology, 42, 3, pp. 601-611, (2021)
[13]  
DAI P,, LIN F., Numerical study on the influence of hole’ s shape on film cooling efficiency[J], Journal of Power Engineering, 29, 2, pp. 117-122, (2009)
[14]  
AL-KHISHALI K J M,, HATEM F F., Film cooling experimental investigation for ramped-conical holes geometry[J], International Journal of Sci⁃ entific and Engineering Research, 10, 4, pp. 736-745, (2013)
[15]  
KIM J H,, KIM K Y., Performance evaluation of a converging-diverging film-cooling hole[J], International Journal of Thermal Sciences, 142, pp. 295-304, (2019)
[16]  
ZHU H R,, Et al., Effect of internal coolant crossflow on the film cooling performance of con⁃ verging slot hole[J], International Journal of Thermal Sciences, 154, (2020)
[17]  
JUBRAN B A., Numerical modelling of film cooling from converging slot-hole[J], Heat and Mass Transfer, 43, 4, pp. 381-388, (2007)
[18]  
YAO Y, ZHANG J Z,, TAN X M., Numerical study of film cooling from converging slot-hole on a gas turbine blade suction side[J], International Communications in Heat and Mass Transfer, 52, pp. 61-72, (2014)
[19]  
DAI H W, ZHANG J H,, REN Y Y,, Et al., Effect of cool⁃ ing hole configurations on combustion and heat transfer in an aero-engine combustor [J], Applied Thermal Engineer⁃ ing, 182, (2021)
[20]  
LIU C L,, XIE G,, ZHU H R., Experimental research on the effect of hole-inclined angle on the film cooling char⁃ acteristics under high mainstream turbulence intensity [J], Journal of Xi'an Jiaotong University, 52, 1, pp. 47-53, (2018)