Heat Storage Characteristic Analysis and Structure Parameter Optimization of Phase Change Heat Storage Unit With Spiral Fin Concentric Sleeve

被引：0

作者：

Gao L. ^{[1
]}

Wang P. ^{[1
]}

Bai J. ^{[1
]}

Sun B. ^{[1
]}

Che D. ^{[1
]}

Li S. ^{[1
]}

机构：

[1] School of Energy and Power Engineering, Northeast Electric Power University, Jilin, 132012, Jilin Province

来源：

Zhongguo Dianji Gongcheng Xuebao/Proceedings of the Chinese Society of Electrical Engineering | 2020年 / 40卷 / 15期

基金：

国家重点研发计划;

关键词：

Concentric sleeve; Enhancement of heat transfer; Melting characteristics; Phase change thermal storage; Spiral-finned; Structure optimization;

D O I：

10.13334/j.0258-8013.pcsee.191713

中图分类号：

学科分类号：

摘要：

In this paper, a concentric trocar phase change heat storage unit filled with palmitate acid was studied. The thermal storage performance test system was established and the phase change heat transfer process was simulated by numerical simulation. By comparing the experimental results with the simulation results, the accuracy of the numerical calculation method was verified. The enhanced heat transfer characteristics of helical rib structure on heat storage unit and the influence of dimensionless pitch and dimensionless rib height on melting process were studied. The results show that under the combined action mechanism of heat conduction and local natural convection of phase change material (PCM), the heating charge time is significantly shortened, and the melting rate increases first and then decreases. Reducing the pitch and increasing the rib height can shorten the charging time, but reduce the heat storage. Based on the analysis of charging time, heat storage and average heat flux, the parameter combinations of dimensionless pitch and rib height are 0.24 and 0.59 by single factor optimization. Under the structure, the heating duration was 240 min, and the average heat flux was 1056W/m2. © 2020 Chin. Soc. for Elec. Eng.

引用

页码：4945 / 4954

页数：9

共 22 条

[1]

Deng Tuoyu, Tian Liang, Liu Jizhen, A control method of heat supply units for improving frequency control and peak load regulation ability with thermal storage in heat supply net, Proceedings of the CSEE, 35, 14, pp. 3626-3633, (2015)

[2]

Dai Yuanhang, Chen Lei, Min Yong, Et al., Optimal dispatch for joint operation of wind farm and combined heat and power plant with thermal energy storage, Proceedings of the CSEE, 37, 12, pp. 3470-3479, (2017)

[3]

Nazir H, Batool M, Osorio F J B, Et al., Recent developments in phase change materials for energy storage applications: a review, International Journal of Heat and Mass Transfer, 129, pp. 491-523, (2019)

[4]

Du Kun, Calautit J, Wang Zhonghua, Et al., A review of the applications of phase change materials in cooling, heating and power generation in different temperature ranges, Applied Energy, 220, pp. 242-273, (2018)

[5]

Xu Zhiguo, Zhao Changying, Ji Yunan, Et al., State-of-the-art of phase-change thermal storage at middle-low temperature, Energy Storage Science and Technology, 3, 3, pp. 179-190, (2014)

[6]

Cai Di, Li Jing, Jiao Naixun, Preparation and thermophysical properties of graphene nanoplatelets-过octadecane phase change composite materials, Acta Physica Sinica, 68, 10, (2019)

[7]

Wei Gaosheng, Wang Yao, Yang Yanping, Et al., Pore-scale numerical simulation of heat transfer enhancement of phase change thermal energy storage materials with porous foam metals, Power Generation Technology, 39, 2, pp. 158-164, (2018)

[8]

Mahdi J M, Lohrasbi S, Ganji D D, Et al., Simultaneous energy storage and recovery in the triplex-tube heat exchanger with PCM, copper fins and Al<sub>2</sub>O<sub>3</sub> nanoparticles, Energy Conversion and Management, 180, pp. 949-961, (2019)

[9]

Mahdi J M, Lohrasbi S, Ganji D D, Et al., Accelerated melting of PCM in energy storage systems via novel configuration of fins in the triplex-tube heat exchanger, International Journal of Heat and Mass Transfer, 124, pp. 663-676, (2018)

[10]

Pizzolato A, Sharma A, Maute K, Et al., Design of effective fins for fast PCM melting and solidification in shell-and-tube latent heat thermal energy storage through topology optimization, Applied Energy, 208, pp. 210-227, (2017)

← 1 2 3 →