FABRICATION OF A TEST RIG FOR GEARBOX FAULT SIMULATION AND DIAGNOSIS

被引：0

作者：

Dubaish A.A. ^{[1
]}

Jaber A.A. ^{[1
]}

机构：

[1] Mechanical Engineering Department, University of Technology- Iraq, Baghdad

来源：

Diagnostyka | 2023年 / 24卷 / 02期

关键词：

fault detection; gearbox; LabVIEW; time-domain signal; vibration analysis;

D O I：

10.29354/DIAG/162541

中图分类号：

学科分类号：

摘要：

Gearboxes are one of the most important and widely exposed to different types of faults in machines. Therefore, manufacturers and researchers have made significant efforts to develop different fault detection and diagnostic approaches for gearboxes. However, many research foundations, such as universities, are currently working on developing different gearbox test rigs to understand the failure mechanisms in gearboxes. As a result, in this article, a gearbox testing rig was proposed and fabricated to evaluate gear performance under low-speed working conditions. It describes the primary mechanical apparatus and the measurement tools used during the experimental analysis of a multistage gearbox transmission system. The data-gathering equipment used to acquire the observed vibration data is also discussed. LabVIEW software was used to build a data acquisition platform using an accelerometer and a NI DAQ device. Then different vibration tests were conducted under different operating conditions, when the gearbox was healthy and then faulty, on this test rig, and the gathered vibration data were analyzed based on time domain signal analysis. The preliminary results are promising and open the horizon for simulating different gearbox test scenarios. © 2023 by the Authors.

引用

共 31 条

[1]

Hunady R, Pavelka P, Lengvarsky P., Vibration and modal analysis of a rotating disc using high-speed 3D digital image correlation, Mechanical Systems and Signal Processing, 121, pp. 201-214, (2019)

[2]

Prieto MD, Cirrincione G, Espinosa AG, Ortega JA, Henao H., Bearing fault detection by a novel condition-monitoring scheme based on statistical-time features and neural networks, IEEE Transactions on Industrial Electronics, 60, 8, pp. 3398-3407, (2012)

[3]

Nikhil T, Chandrahas T, Chaitanya C, Ingle SR, Sabareesh GR, Design and Development of a Test-Rig for Determining Vibration Characteristics of a Beam, Procedia Engineering, 144, pp. 312-320, (2016)

[4]

Fessett DJ, Hardware for Testing Gear Transmissions, Mach Des, 47, 19, pp. 80-83, (1975)

[5]

Bediaga I, Mendizabal X, Arnaiz A, Munoa J., Ball bearing damage detection using traditional signal processing algorithms, IEEE Instrumentation & Measurement Magazine, 16, 2, pp. 20-25, (2013)

[6]

Guan L, Shao Y, Gu F, Fazenda B, Ball A, Gearbox fault diagnosis under different operating conditions based on time synchronous average and ensemble empirical mode decomposition, ICCAS-SICE 2009 - ICROS-SICE International Joint Conference Proceedings, pp. 383-388, (2009)

[7]

Dhamande LS, Pawar AC, Suryawanshi VJ., Detection of Fault in Gear Box System using Vibration Analysis Method, International Journal of Current Engineering and Technology, 39854, 6, pp. 119-122, (2014)

[8]

Suresh S, Mallimoggala S, VPS N, Vibration Analysis of Gearbox Fault Diagnosis using DWT and Statistical Features, Journal of Engineering Research, (2021)

[9]

Al-Arbi S, Gu F, Guan L, Ball A, Naid A., Gearbox fault diagnosis based on vibration signals measured remotely, Key Engineering Materials, pp. 175-414, (2009)

[10]

Praveenkumar T, Saimurugan M, Krishnakumar P, Ramachandran KI., Fault Diagnosis of Automobile Gearbox Based on Machine Learning Techniques, Procedia Engineering, 97, pp. 2092-2098, (2014)

← 1 2 3 4 →