Anti-impact characteristics of thrust bearing considering elastic deformation

被引：0

作者：

Zhou X. ^{[1
,2
]}

Qi S. ^{[1
,2
]}

Liu H. ^{[1
,2
]}

机构：

[1] Lubrication Theory and Bearing Research Institute, Xi'an Jiaotong University, Xi'an

[2] Key Laboratory of Education Ministry for Modern Design and Rotor-Bearing System, Xi'an Jiaotong University, Xi'an

来源：

Zhendong yu Chongji/Journal of Vibration and Shock | 2021年 / 40卷 / 15期

关键词：

Impact resistance; Response analysis; Structural elastic deformation; Thrust bearing;

D O I：

10.13465/j.cnki.jvs.2021.15.010

中图分类号：

学科分类号：

摘要：

Here, aiming at a thrust sliding bearing of a rolling bearing testing machine subjected to transient impact load, the dynamic model for the thrust bearing-rotor system and the simplified bearing pedestal structural deformation model were established. Reynolds equation for thrust bearing oil film was solved with the finite element method, the axial dynamic equation of the rotating shaft was solved using Euler integral method, and the structural deformation of bearing pedestal was solved with ANSYS simulation. Through the combined solving, variations of the thrust bearing's oil film resultant force, minimum oil film thickness and flow rate with time varying in impact process were obtained. Impact responses of the thrust bearing considering and not considering structural deformation of bearing pedestal were compared. The results showed that effects of bearing pedestal elastic deformation on oil film resultant force and minimum oil film thickness can't be ignored; without considering structural deformation, response speeds of oil film resultant force and minimum oil film thickness are much faster, and their response time decreases by about 22%; elastic deformation delays response process, it acts as a buffer and shortens the time required to reach the system's steady state; when elastic deformation is considered or not, the maximum value of oil film resultant force and the minimum value of the minimum oil film thickness are basically the same; appropriate structural stiffness of bearing pedestal can improve the anti-impact ability of thrust bearing; the structural stiffness should not be less than a certain critical value, too small structural stiffness may cause the minimum oil film thickness of a certain tile to be very small and hard to bear large transient impact load; too large structural stiffness may cause bearing pedestal structure to be complex without buffering effect, and some connectors to fail too early. © 2021, Editorial Office of Journal of Vibration and Shock. All right reserved.

引用

页码：73 / 78and89

页数：7816

共 15 条

[1]

KENNEDY J S, SABHAPATHY P, RODKIEWICZ C M., Transient thermal effects in an infinite tilted-pad slider bearing, Tribology Transactions, 32, 1, pp. 47-53, (1989)

[2]

FU Yanli, MA Xizhi, ZHU Jun, Three-dimensional thermohydrodynamic analysis of circular journal bearing, Journal of Aerospace Power, 4, pp. 86-91, (2002)

[3]

TICHY J, BOU-SAID B., Hydrodynamic lubrication and bearing behavior with impulsive loads, Tribology Transactions, 34, 4, pp. 505-512, (1991)

[4]

RAO T V V L N, BISWAS S, HIRANI H, Et al., An analytical approach to evaluate dynamic coefficients and nonlinear transient analysis of a hydrodynamic journal bearing, Tribology Transactions, 43, 1, pp. 109-115, (2000)

[5]

MA Xizhi, ZHU Jun, Thermal transient behavior of thrust bearing under step applied load, Lubrication Engineering, 34, 1, pp. 43-45, (2009)

[6]

MA Xizhi, ZHU Jun, A Study on adiabatic transient behavior of thrust bearing under dynamic operating load, Lubrication Engineering, 34, 3, pp. 49-52, (2009)

[7]

ZHANG Shenglun, PEI Shiyuan, XU Hua, Et al., Journal bearing properties and dynamic responses under transient impact load and elastic deformation, Journal of Xi'an Jiaotong University, 52, 1, pp. 100-106, (2018)

[8]

(1986)

[9]

(1998)

[10]

QI Shemiao, GENG Haipeng, YU Lie, New method for the calculation of the characteristics of aerodynamic bearings, Journal of Mechanical Strength, 28, 3, pp. 369-373, (2006)

← 1 2 →