Experimental Study on Mechanical Properties of Ductile-Iron Joint Panels for Segmental Joints in Deep-Buried Drainage Shield Tunnels

被引：0
作者：
Yan Z. [1 ,2 ,3 ]
Zhou L. [3 ]
Zhu H. [1 ,2 ,3 ]
Shen Y. [1 ,2 ]
机构：
[1] State Key Laboratory of Disaster Reduction in Civil Engineering, Tongji University, Shanghai
[2] Key Laboratory of Geotechnical and Underground Engineering of the Ministry of Education, Tongji University, Shanghai
[3] College of Civil Engineering, Tongji University, Shanghai
来源：
Tongji Daxue Xuebao/Journal of Tongji University | 2019年 / 47卷 / 03期
关键词：
Deep-buried drainage shield tunnel; Ductile-iron joint panel; Experiment; High-stiffness segmental joint;
D O I：
10.11908/j.issn.0253-374x.2019.03.005
中图分类号：
学科分类号：
摘要：
To study the applicability of DIJPs (ductile-iron joint panels) suitable for deep-buried drainage shield tunnels, positive bending moment tests for HSSJs with two different types of DIJPs were carried out, and the mechanical properties of DIJPs and the failure modes of HSSJs were analyzed. The experimental results show that: the failure characteristic of HSSJs subjected to positive bending moment, which is similar to the failure characteristic of the compression-bending section with large eccentricity, is that the bolts or the DIJPs yield firstly, and then the segmental joint fails with the concrete in the compressive zone broken. If the flexural rigidity of the DIJPs is sufficient, there is no deformation in the DIJPs, the bearing capacity of the segmental joint is higher, and the anchor bars reach their full potential; if the flexural rigidity of the DIJPs is insufficient, 5 mm bending deflection appears in the DIJPs, the bearing capacity of the segmental joint is lower, and the anchor function of anchor bars is not fully exploited. © 2019, Editorial Department of Journal of Tongji University. All right reserved.
引用
收藏
页码：331 / 338
页数：7
相关论文
共 20 条
  • [11] Zhu H., Huang B., Li X., Et al., Unified model for internal force and deformation of shield segment joints and experimental analysis, Chinese Journal of Geotechnical Engineering, 36, 12, (2014)
  • [12] Li X.J., Yan Z.G., Wang Z., Et al., A progressive model to simulate the full mechanical behavior of concrete segmental lining longitudinal joints, Engineering Structures, 93, (2015)
  • [13] Koyama Y., Present status and technology of shield tunneling method in Japan, Tunnelling and Underground Space Technology, 18, 2, (2003)
  • [14] Jin Y.L., Ding W.Q., Yan Z.G., Et al., Experimental investigation of the nonlinear behavior of segmental joints in a water-conveyance tunnel, Tunnelling and Underground Space Technology, 68, (2017)
  • [15] Yan Z., Ding W., Shen B., Et al., Structural model for radial joints of water-conveyance shield tunnels, Chinese Journal of Geotechnical Engineering, 33, 8, (2011)
  • [16] Ding Y.N., Liu H.K., Pacheco-Torgal F., Et al., Experimental investigation on the mechanical behaviour of the fiber reinforced high-performance concrete tunnel segment, Composite Structures, 93, 4, (2011)
  • [17] Gong C., Ding W., Experimental investigation on ultimate bearing capacity of steel fiber reinforced concrete segment joints in shield tunnels, China Journal of Highway and Transport, 30, 8, (2017)
  • [18] Jin Y., Ding W., Jiang H., Et al., Test on ultimate bearing capacity of segment joint in shield tunnel with large rectangular cross-section, China Journal of Highway and Transport, 30, 8, (2017)
  • [19] Standard for test method of concrete structures: GB/T 50152-2012, (2012)
  • [20] Liu X., Zhang C., Zhang C., Investigation on the ultimate bearing capacity of longitudinal joints in segmental tunnel lining, China Civil Engineering Journal, 49, 10, (2016)
12