Characterization of an Al-Cu alloy using fly ash and graphite metal matrix composite

被引：1

作者：

Vishwanath S. ^{[1
]}

Kumar R. ^{[2
]}

Anand P. ^{[3
]}

Bhandari N. ^{[4
]}

机构：

[1] Government of Gujarat, Industrial Extension Bureau, Gujarat

[2] Mechanical Engineering, Birla Institute of Technology Mesra, Jharkhand, Ranchi

[3] Civil Engineering, Birla Institute of Technology Mesra, BIT, Jharkhand, Ranchi

[4] Project Engineer, iGAS Technology Solutions, Karnataka, Bangalore

来源：

Materials Today: Proceedings | 2023年 / 74卷

关键词：

Composites; Fly ash; Graphite; Metal matrix; Wear;

D O I：

10.1016/j.matpr.2022.10.212

中图分类号：

学科分类号：

摘要：

The Al-Cu alloy is used as the main matrix material in this study, with fly ash and graphite added in. Aluminum-copper alloy composites are very popular for a number of reasons, including their good thermal conductivity and ability to work in moderate temperatures. Since graphite and fly ash particles are thin and strong, they can be used as reinforcing materials. The process of stir casting was used to make the composite. Fly ash and graphite particles were also added to the molten Al-Cu alloy in amounts of 3%, 6%, and 9%, respectively. After that, the mechanical properties of the composite were glanced at. These included tensile strength. SEM microstructure analysis was used to figure out how well graphite and fly ash particles should be spread out in the Al-Cu matrix. The density of composites goes down as the amount of reinforcement materials rises. In furthermore, the addition of the reinforcing particle improves the wearability of the surface. The specimen used in the experiment is made to meet the standards set by ASTM. © 2022

引用

页码：663 / 666

页数：3

共 17 条

[1]

Babu Rao J., Rao D.V., Catherin G.J., Bhargava N.R.M.R., Development of Light Weight AA2024 Alpha Composites, Mater. Sci. Forum, 690, pp. 258-261, (2011)

[2]

Kumar R., Deshpande R.G., Gopinath B., Harti J., Nagaral M., Auradi V., Mechanical Fractography and Worn Surface Analysis of Nanographite and ZrO2-Reinforced Al7075 Alloy Aerospace Metal Composites, J. Fail. Anal. Prev., 21, 2, pp. 525-536, (2021)

[3]

Siddesh Kumar N.G., Shiva Shankar G.S., Basavarajappa S., Suresh R., Some studies on mechanical and machining characteristics of Al2219/n-B4C/MoS2 nano-hybrid metal matrix composites, Measurement, 107, pp. 1-11, (2017)

[4]

Sunil Kumar Reddy K., Kannan M., Karthikeyan R., Sripad A., Jain P.K., Investigation of thermal and mechanical properties of Al7020/SiC/graphite hybrid metal matrix composites, Mater. Today Proc., 26, pp. 2746-2753, (2020)

[5]

Sakthivelu S., Sethusundaram P.P., Ravichandran M., Meignanamoorthy M., Experimental Investigation and Analysis of Properties and Dry Sliding Wear Behavior of Al -Fe-Si Alloy Matrix Composites, Silicon, 13, 4, pp. 1285-1294, (2021)

[6]

Santhanam V., Dhanaraj R., Chandrasekaran M., Venkateshwaran N., Baskar S., Experimental investigation on the mechanical properties of woven hybrid fiber reinforced Epoxy composite, Mater. Today Proc., Available online, (2020)

[7]

Baskar S., Vijayan V., Saravanan S., Balan A.V., 9, 12, pp. 91-96

[8]

Venkat Prasat S., Subramanian R., Tribological properties of AlSi10Mg/fly ash/graphite hybrid metal matrix composites, Ind. Lubr. Tribol., 65, 6, pp. 399-408, (2013)

[9]

Bhaskar K.V., Sundarrajan S., Krishna M.G., Ravindra K., Microstructure and Mechanical properties of Flyash/SiC Particles Reinforced AA 2024 Hybrid Composites, Mater. Today Proc., 4, 8, pp. 7413-7419, (2017)

[10]

Venkat Prasat S., Subramanian R., Radhika N., Anandavel B., Dry sliding wear and friction studies on AlSi10Mg–fly ash–graphite hybrid metal matrix composites using Taguchi method, Tribol. - Mater. Surf. Interfaces, 5, 2, pp. 72-81, (2011)

← 1 2 →