Fault Distance Location of Active Distribution Network Based on 2-Norm Current Deviation

被引：0
作者：
Liu X. [1 ,2 ]
Teng H. [1 ,2 ]
Liang M. [3 ]
Teng D. [1 ,2 ]
机构：
[1] Smart Grid Sichuan Key Laboratory, Sichuan University, Chengdu
[2] School of Electrical Information, Sichuan University, Chengdu
[3] State Grid Xinxiang Power Supply Company, Xinxiang
来源：
Diangong Jishu Xuebao/Transactions of China Electrotechnical Society | 2019年 / 34卷
关键词：
Active distribution network; Distribution generation; Fault area identification; Fault distance positioning;
D O I：
10.19595/j.cnki.1000-6753.tces.L80073
中图分类号：
学科分类号：
摘要：
The access of the distributed power supply will affect or even invalidate the fault location algorithm of the traditional distribution network. Therefore, this paper proposes a fault location algorithm based on current deviation 2-norm. The algorithm firstly injects a unit current into each node of the distribution network, and obtains a linear proportional coefficient by matching the calculated value of the system power outlet current change with the measured value before the fault; then, correcting the current response value of the distributed power source, and then The current variation is subjected to 2-norm current deviation processing; finally, the fault region identification and fault distance location are performed by the node with the smallest current deviation. The algorithm takes into account the non-equilibrium characteristics of the active distribution network, and does not need to predict the type of fault, and has wide adaptability. By constructing the simulation model of the active distribution network on PSCAD/EMTDC, the fault data processing is performed on Matlab, which verifies the effectiveness and accuracy of the fault location algorithm. © 2019, Electrical Technology Press Co. Ltd. All right reserved.
引用
收藏
页码：720 / 728
页数：8
相关论文
共 13 条
  • [1] Li Z., Wang X., Tian B., Et al., Fast fault location based on voltage distribution law along the line, Transactions of China Electrotechnical Society, 33, 1, pp. 112-120, (2018)
  • [2] Chen Y., Liu Z., Chen Z., A fast diagnosis and location method for open circuit faults of inverters based on current vector feature analysis, Transactions of China Electrotechnical Society, 33, 4, pp. 883-891, (2018)
  • [3] Zhang X., Tai N., Zheng X., Et al., Fault location of flexible DC transmission lines based on WEMTR, Transactions of China Electrotechnical Society, 34, 3, pp. 589-598, (2019)
  • [4] Deng F., Li X., Zeng X., A single- ended traveling wave location method for hybrid transmission lines based on full waveform information, Transactions of China Electrotechnical Society, 33, 15, pp. 3471-3485, (2018)
  • [5] Da Silva Pessoa A.L., Oleskovicz M., Fault location in radial distribution systems based on decision trees and optimized allocation of power quality meters, 2017 IEEE Manchester PowerTech, pp. 1-6, (2017)
  • [6] Shao W., Xu G., Luo H., Et al., Design and implementation of fault location system for intelligent distribution network, Electrical Engineering, 2, pp. 77-80, (2016)
  • [7] Fan P., Cao R., He Q., Et al., Application analysis of active fault location system for distribution lines, Electrical Engineering, 12, (2016)
  • [8] Wang Q., Jin T., Tan H., Et al., Fault location technology for distribution network based on hierarchical model and intelligent check algorithm, Transactions of China Electrotechnical Society, 33, 22, pp. 5327-5337, (2018)
  • [9] Niu G., Zhou L., Pei W., Et al., On-line fault interval location and identification method for low-voltage active distribution network, Proceedings of the CSEE, 37, 9, pp. 2525-2537, (2017)
  • [10] Liu T., Liu J., Xiao X., Et al., A new method for single-wire grounding line selection in distribution network based on wavelet singular entropy and support vector machine, Power System and Clean Energy, 33, 2, pp. 14-20, (2017)
12