Microstructure Characterization and Tribological Properties Evaluation on WC/Cu Composite Coating Prepared by Supersonic Laser Deposition

被引：0
作者：
Huang X. [1 ,2 ]
Wu L. [1 ,2 ]
Li B. [1 ,2 ]
Wang W. [1 ,2 ]
Zhang Q. [1 ,2 ]
Kovalenko V.S. [1 ,3 ]
Yao J. [1 ,2 ]
机构：
[1] Institute of Laser Advanced Manufacturing, Zhejiang University of Technology, Hangzhou
[2] Zhejiang Provincial Collaborative Innovation Center of High-end Laser Manufacturing Equipment, Hangzhou
[3] Laser Technology Research Institute, National Technical University of Ukraine, Kiev
来源：
Jixie Gongcheng Xuebao/Journal of Mechanical Engineering | 2020年 / 56卷 / 10期
关键词：
Microhardness; Microstructure; Solid-state deposition; Supersonic laser deposition; WC/Cu composite coatings; Wear-resistance;
D O I：
10.3901/JME.2020.10.078
中图分类号：
学科分类号：
摘要：
Pure copper has good conductivity of heat and electricity, but low hardness and poor wear resistance. Therefore, the WC/Cu composite coatings are prepared on the surface of copper substrate by supersonic laser deposition (SLD) and cold spray (CS). The microstructure, phase composition, microhardness and wear property of the as-prepared coatings are comparatively analyzed for these two technologies. The results show that the thickness of CS coating is about 1 128 μm, the WC content is 7.73% and the microhardness is 147.4 HV0.2, but there are some gaps at the coating/substrate bonding zone. For SLD coating, the thickness increases with elevating laser power. The thickest coating thickness is up to 2 344 μm, the highest WC content is 17.22% and the highest microhardness reaches 161.3 HV0.2. All SLD coatings show well-bonded coating/substrate interface. The SLD coating still retains the original phase composition of the feedstock powder. However, samples prepared at high laser power experienced slight oxidation. The wear resistance of the SLD coating is superior to that of the CS coating and Cu substrate, with lower coefficient of friction, wear scar width and wear loss. These results provide a new route for improving the surface properties of Cu and its alloys. © 2020 Journal of Mechanical Engineering.
引用
收藏
页码：78 / 85
页数：7
相关论文
共 23 条
[1]  
ZHANG Yuefei, SU Yongan, CHEN Fei, Research on high strength and high conductivity copper-based materials, Heat Treatment of Metals Abroad, 22, pp. 6-9, (2001)
[2]  
LIU Tao, LI Jian, LING Guoping, Et al., Progress in studies of particle reinforced Cu-matrix composites, Materials Review, 18, pp. 53-55, (2004)
[3]  
IBRAHIM A E A M, KIM H S., Effect of the fabrication method on the wear properties of copper silicon carbide composites, Tribology International, 128, pp. 140-154, (2018)
[4]  
WANG Y, CHEN M, ZHOU F, Et al., High tensile ductility in a nanostructured metal, Nature, 419, 6910, pp. 912-915, (2002)
[5]  
YUAN Junrui, XU Jia, ZHOU Zhenyu, Et al., Study on wear behavior of gradient nanocrystalline structure on pure copper surface induced by burnishing, Journal of Mechanical Engineering, 53, 24, pp. 49-54, (2017)
[6]  
KANG H K., Microstructure and electrical conductivity of high volume Al<sub>2</sub>O<sub>3</sub>-reinforced copper matrix composites produced by plasma spray, Surface & Coatings Technology, 190, 2-3, pp. 448-452, (2005)
[7]  
LIU Debao, CUI Chunxiang, MA Xu, Surface coating copper on AIN particle and AIN particle-reinforced copper matrix composites, Ordnance Material Science and Engineering, 28, 2, pp. 8-11, (2005)
[8]  
DESHPANDE P K, LI J H, LIN R Y., Infrared processed Cu composites reinforced with WC particles, Materials Science & Engineering A (structural materials: properties, microstructure and processing), 429, 1-2, pp. 58-65, (2006)
[9]  
YANG Guirong, SONG Wenming, HAO Yuan, Et al., Microstructure and properties of Ni/Al2O3 composite infiltrated layer on copper surface, Corrosion & Protection, 28, 6, pp. 275-278, (2007)
[10]  
ZENG Aixiang, TANG Shaoqiu, Preparation, application and development of metal-based ceramic coatings, Ceramic Studies Journal, 4, pp. 7-10, (1998)
123