Effect of Data Mode from Stress-Strain Curve on Forming Limit of Aluminum Alloy Sheets

被引：1

作者：

Cai Z.-Y. ^{[1
,2
]}

Li L. ^{[1
]}

Sun L.-R. ^{[1
]}

Meng F.-X. ^{[1
]}

机构：

[1] College of Materials Science and Engineering, Jilin University, Changchun

[2] Roll Forging Research Institute, Jilin University, Changchun

来源：

Dongbei Daxue Xuebao/Journal of Northeastern University | 2020年 / 41卷 / 03期

关键词：

Forming limit diagram(FLD); M-K theory; Metal sheet; Stress-strain curve; Theoretical prediction;

D O I：

10.12068/j.issn.1005-3026.2020.03.025

中图分类号：

学科分类号：

摘要：

In order to analyze sheet formability more realistically, a new approach based on the M-K theory was proposed, which predicted the forming limit of aluminum alloy sheets by using different modes of data from the measured stress-strain curve. The forming limits of 6016-T4 and 7075-T6 aluminum alloy sheets were theoretically analyzed using three modes of data, which were the original data of the measured stress-strain curve, the power exponential fitted data and polynomial fitted data of the stress-strain curves, respectively. According to the stress-strain data from tensile test, the ultimate strains were calculated and the theoretical forming limit curves (FLC) were plotted. After comparing the theoretically predicted FLC with experimental data from the bulging test, the results indicate that the predicted forming limits using the data of the original stress-strain curve is the best one, while the forming limits using the data from the power exponential fitted curve has a certain deviation from the experimental one. © 2020, Editorial Department of Journal of Northeastern University. All right reserved.

引用

页码：445 / 451

页数：6

共 10 条

[1]

Yang X.-M., Wang B.-Y., Xiao W.-C., Et al., Prediction of forming limit curve of 6016 aluminum alloy based on M-K theory, Chinese Journal of Engineering, 40, 4, pp. 485-491, (2018)

[2]

Zhang X.S., Chen Y.J., Hu J.L., Recent advances in the development of aerospace materials, Progress in Aerospace Sciences, 97, pp. 22-34, (2018)

[3]

Zhang Q., Lang L.H., Zhang Y.F., Et al., Application of the modified critical voids expansion ratio criterion to the prediction of the forming limit of 6016-O aluminum alloy, The International Journal of Advanced Manufacturing Technology, 98, 5-8, pp. 2069-2082, (2018)

[4]

Banabic D., Advances in plastic anisotropy and forming limits in sheet metal forming, Journal of Manufacturing Science and Engineering, 138, 9, (2016)

[5]

Marciniak Z., Kuczynski K., Limit strains in the processes of stretch-forming sheet metal, International Journal of Mechanical Science, 9, 3, pp. 609-620, (1967)

[6]

Marciniak Z., Kuczynski K., Pokora T., Influence of the plastic properties of a material on the forming limit diagram for sheet metal in tension, International Journal of Mechanical Sciences, 15, 10, pp. 789-800, (1973)

[7]

Du P.-M., Lang L.-H., Liu B.-S., Et al., Theoretical prediction and parameter influence of FLDs based on M-K model, Journal of Plasticity Engineering, 18, 5, pp. 84-89, (2011)

[8]

Abedrabbo N., Pourboghrat F., Carsley J., Forming of AA5182-O and AA5754-O at elevated temperatures using coupled thermo-mechanical finite element models, International Journal of Plasticity, 23, pp. 841-875, (2007)

[9]

Li X.Q., Guo G.Q., Xiao J.J., Et al., Constitutive modeling and the effects of strain-rate and temperature on the formability of Ti-6Al-4V alloy sheet, Materials & Design, 55, pp. 325-334, (2014)

[10]

Chu G.-N., Lin Y.-L., Song W.-N., Et al., Forming limit of FSW aluminum alloy blank based on a new constitutive model, Acta Metallurgica Sinica, 53, 1, pp. 114-122, (2017)

← 1 →