HEAT-TRANSFER ANALYSIS DURING WATER SPRAY COOLING OF STEEL RODS

被引：54
|
作者：
MORALES, RD [1 ]
LOPEZ, AG [1 ]
OLIVARES, IM [1 ]
机构：
[1] HYLSA SN,PUEBLA STEELWORKS,MIGUEL XOXTLA,PUEBLA,MEXICO
来源：
ISIJ INTERNATIONAL | 1990年 / 30卷 / 01期
关键词：
cooling-rate reheating; drawing; finishing mill; flow-rate; heat-transfer; pearlitic transformation; rod; speed; steel; Stelmor Process; water-spray; wire;
D O I：
10.2355/isijinternational.30.48
中图分类号：
TF [冶金工业];
学科分类号：
0806 ;
摘要：
A mathematical model has been developed to predict the rod cooling behavior of steel rods under the action of water sprays in the precooling system of a Stelmor machine. The main objective of this work was to study the influence of operation parameters such as rod size, rod speed, rod temperature at the finishing mill, water flow-rate and spray cooling sequence on the final temperature distribution within the rod before it enters into the transformation conveyor. This heat transfer analysis indicates that the spray cooling sequence affects, considerably, the temperature distribution inside the rod. Besides, water flow-rate failures in the spray cooling system disturb drastically its cooling efficiency. Finally, reheating phenomena which go from 150 to 200°C at rod surface are predicted. The calculations were validated with in situ experimental measurements carried out at HyLSA's (Puebla Plant) Stelmor machine. Very good agreement was found between predicted and experimentally measured rod surface temperatures. © 1990, The Iron and Steel Institute of Japan. All rights reserved.
引用
收藏
页码：48 / 57
页数：10
相关论文
共 50 条
  • [31] Experimental investigation of parameters effect on heat transfer of spray cooling
    Wen-Long Cheng
    Qi-Nie Liu
    Rui Zhao
    Han-lin Fan
    Heat and Mass Transfer, 2010, 46 : 911 - 921
  • [32] Surface orientation effects on heat transfer performance of spray cooling
    Zhao, Xiao
    Zhang, Bo
    Yang, Zhuogiang
    Zhao, Yuxin
    INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2020, 147
  • [33] Functional Surfaces with Enhanced Heat Transfer for Spray Cooling Technology
    S. A. Romashevskiy
    A. V. Ovchinnikov
    High Temperature, 2018, 56 : 255 - 262
  • [34] SIMULATION AND CONTROL OF HEAT-TRANSFER IN CONTINUOUS-CASTING OF STEEL
    LOUHENKILPI, S
    ACTA POLYTECHNICA SCANDINAVICA-CHEMICAL TECHNOLOGY SERIES, 1995, (230): : 1 - 37
  • [35] LOCAL HEAT-TRANSFER FOR SUBCOOLED FLOW BOILING WITH WATER
    BOYD, RD
    MENG, XW
    FUSION TECHNOLOGY, 1992, 22 (04): : 501 - 510
  • [36] DISK HEAT-TRANSFER IN A ROTATING CAVITY WITH AN AXIAL THROUGHFLOW OF COOLING AIR
    LONG, CA
    INTERNATIONAL JOURNAL OF HEAT AND FLUID FLOW, 1994, 15 (04) : 307 - 316
  • [37] HEAT-TRANSFER CHARACTERISTICS OF COAL-WATER MIXTURES
    SAEKI, T
    USUI, H
    CANADIAN JOURNAL OF CHEMICAL ENGINEERING, 1995, 73 (03) : 400 - 404
  • [38] A heat-transfer analysis of the ferrite sintering process
    Rek, Z
    Perpar, M
    Zun, I
    STROJNISKI VESTNIK-JOURNAL OF MECHANICAL ENGINEERING, 2002, 48 (09): : 472 - 481
  • [39] EXPERIMENTAL-STUDY OF HEAT-TRANSFER IN-PROCESS OF ROLLS COOLING IN ROLLING-MILLS BY WATER JETS
    RAUDENSKY, M
    BENDING, L
    HORSKY, J
    STEEL RESEARCH, 1994, 65 (01): : 29 - 35
  • [40] Dynamic pressure based prediction of spray cooling heat transfer coefficients
    Abbasi, Bahman
    Kim, Jungho
    Marshall, Andre
    INTERNATIONAL JOURNAL OF MULTIPHASE FLOW, 2010, 36 (06) : 491 - 502
12345