HEAT-TRANSFER ANALYSIS DURING WATER SPRAY COOLING OF STEEL RODS

被引：54
|
作者：
MORALES, RD [1 ]
LOPEZ, AG [1 ]
OLIVARES, IM [1 ]
机构：
[1] HYLSA SN,PUEBLA STEELWORKS,MIGUEL XOXTLA,PUEBLA,MEXICO
来源：
ISIJ INTERNATIONAL | 1990年 / 30卷 / 01期
关键词：
cooling-rate reheating; drawing; finishing mill; flow-rate; heat-transfer; pearlitic transformation; rod; speed; steel; Stelmor Process; water-spray; wire;
D O I：
10.2355/isijinternational.30.48
中图分类号：
TF [冶金工业];
学科分类号：
0806 ;
摘要：
A mathematical model has been developed to predict the rod cooling behavior of steel rods under the action of water sprays in the precooling system of a Stelmor machine. The main objective of this work was to study the influence of operation parameters such as rod size, rod speed, rod temperature at the finishing mill, water flow-rate and spray cooling sequence on the final temperature distribution within the rod before it enters into the transformation conveyor. This heat transfer analysis indicates that the spray cooling sequence affects, considerably, the temperature distribution inside the rod. Besides, water flow-rate failures in the spray cooling system disturb drastically its cooling efficiency. Finally, reheating phenomena which go from 150 to 200°C at rod surface are predicted. The calculations were validated with in situ experimental measurements carried out at HyLSA's (Puebla Plant) Stelmor machine. Very good agreement was found between predicted and experimentally measured rod surface temperatures. © 1990, The Iron and Steel Institute of Japan. All rights reserved.
引用
收藏
页码：48 / 57
页数：10
相关论文
共 50 条
  • [1] Effect of Spray Pressure and Height on Interfacial Heat Transfer of H13 Steel during Spray Cooling
    Wang, Zi-Chao
    Zhao, Hai-Dong
    Wang, Guo
    Lei, Yue-Qin
    ISIJ INTERNATIONAL, 2022, 62 (01) : 149 - 156
  • [2] THE FINITE-ELEMENT ANALYSIS OF TRANSIENT HEAT-TRANSFER IN FRESH TOMATOES DURING COOLING
    PAN, JC
    BHOWMIK, SR
    TRANSACTIONS OF THE ASAE, 1991, 34 (03): : 972 - 976
  • [3] Study on heat transfer performance of spray cooling: model and analysis
    Rui Zhao
    Wen-long Cheng
    Qi-nie Liu
    Han-lin Fan
    Heat and Mass Transfer, 2010, 46 : 821 - 829
  • [4] Experimental investigation on heat transfer of spray cooling with the mixture of ethanol and water
    Liu, Hong
    Cai, Chang
    Yin, Hongchao
    Luo, Jia
    Jia, Ming
    Gao, Jiuliang
    INTERNATIONAL JOURNAL OF THERMAL SCIENCES, 2018, 133 : 62 - 68
  • [5] Effect of skin indentation on heat transfer during cryogen spray cooling
    Basinger, B
    Aguilar, G
    Nelson, JS
    LASERS IN SURGERY AND MEDICINE, 2004, 34 (02) : 155 - 163
  • [6] Analysis on the influences of atomization characteristics on heat transfer characteristics of spray cooling
    Bao, Jun
    Wang, Yu
    Xu, Xinjie
    Niu, Xiaoyi
    Liu, Jinxiang
    Qiu, Lanlan
    SUSTAINABLE CITIES AND SOCIETY, 2019, 51
  • [7] Spray cooling heat transfer: The state of the art
    Kim, Jurigho
    INTERNATIONAL JOURNAL OF HEAT AND FLUID FLOW, 2007, 28 (04) : 753 - 767
  • [8] Computer modeling of liquid droplet impact on heat transfer during spray cooling
    Selvam, R. Panneer
    Bhaskara, Sandya
    Balda, Juan C.
    Barlow, Fred
    Elshabini, Aicha.
    HT2005: Proceedings of the ASME Summer Heat Transfer Conference 2005, Vol 2, 2005, : 179 - 188
  • [9] Heat transfer in a water film falling along a heat-transfer surface during its contact with air
    Voinov N.A.
    Eremenko N.A.
    Nikolaev N.A.
    Thermal Engineering, 2007, 54 (4) : 324 - 331
  • [10] Heat-transfer characteristics during rapid quenching of a thin wire in water
    Honda, Hiroshi
    Takamatsu, Hiroshi
    Yamashiro, Hikaru
    Kobayashi, Shintaro
    Heat Transfer - Japanese Research, 1992, 21 (08): : 773 - 791
12345