ATMOSPHERE CONTROL DURING DEBINDING OF POWDER INJECTION-MOLDED PARTS

被引：6
|
作者：
MOORE, JA
JARDING, BP
LOGRASSO, BK
ANDERSON, IE
机构：
[1] Ames Laboratory, Metallurgy and Ceramics Div., Iowa State University, Ames, Iowa
来源：
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE | 1995年 / 4卷 / 03期
关键词：
DEBINDING; SINTERING; INJECTION MOLDING;
D O I：
10.1007/BF02649064
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Atmosphere control during debinding of powder injection molded (PIM) parts is an important parameter to consider. Experimental results have shown that a stagnant atmosphere containing volatiles evolved during debinding can cause slumping of the green samples. Removal of volatiles from the sample zone aids debinding and can reduce cycle times and improve sample quality. Residual carbon and oxygen can be controlled during debinding by adjusting the atmosphere composition. This paper presents the results of PIM 70 vol% spherical copper powder and 30 vol% binder. Debinding atmospheres were altered to determine the effect of debinding on the green body and the sintered sample.
引用
收藏
页码：275 / 282
页数：8
相关论文
共 50 条
  • [31] Control of gloss defect on high-gloss injection-molded surfaces
    Jinsu Gim
    Byungohk Rhee
    Korea-Australia Rheology Journal, 2021, 33 : 133 - 141
  • [32] Control of gloss defect on high-gloss injection-molded surfaces
    Gim, Jinsu
    Rhee, Byungohk
    KOREA-AUSTRALIA RHEOLOGY JOURNAL, 2021, 33 (02) : 133 - 141
  • [33] Preliminary sintering study of powder injection molded WC/Co parts
    Cora, V. S.
    Brandusan, L.
    Vida-Simiti, I.
    Thalmaier, Gy.
    OPTOELECTRONICS AND ADVANCED MATERIALS-RAPID COMMUNICATIONS, 2012, 6 (9-10): : 941 - 944
  • [34] The Modification of Useful Injection-Molded Parts' Properties Induced Using High-Energy Radiation
    Bednarik, Martin
    Pata, Vladimir
    Ovsik, Martin
    Mizera, Ales
    Husar, Jakub
    Manas, Miroslav
    Hanzlik, Jan
    Karhankova, Michaela
    POLYMERS, 2024, 16 (04)
  • [35] Deformation analysis of short glass fiber-reinforced polypropylene injection-molded plastic parts
    Siklo, B.
    Cameron, K.
    Kovacs, J. G.
    JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2011, 30 (16) : 1367 - 1372
  • [36] Residual stress distributions and their influence on post-manufacturing deformation of injection-molded plastic parts
    Kim, Beomkeun
    Min, Juwon
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2017, 245 : 215 - 226
  • [37] Effect of Increased Weight Reduction on Shrinkage of Injection-Molded Parts Using Microcellular Foaming Process
    Zafar, Rizwan
    Lee, Kyung Soo
    Kim, Hak Bin
    Jeon, Byung Joo
    Cha, Sung Woon
    POLYMER-PLASTICS TECHNOLOGY AND ENGINEERING, 2008, 47 (11) : 1187 - 1192
  • [38] Effect of Chemical Modification on Mechanical Properties of Wood-Plastic Composite Injection-Molded Parts
    Sohn, Joo Seong
    Cha, Sung Woon
    POLYMERS, 2018, 10 (12)
  • [39] Optical characteristics of injection-molded fluorene polymers
    Kato, Mariko
    Ito, Hiroshi
    JOURNAL OF POLYMER ENGINEERING, 2013, 33 (06) : 557 - 563
  • [40] Melting and crystallization behaviors of injection-molded polypropylene
    Fujiyama, M
    Masada, I
    Mitani, K
    JOURNAL OF APPLIED POLYMER SCIENCE, 2000, 78 (10) : 1751 - 1762
12345