ATMOSPHERE CONTROL DURING DEBINDING OF POWDER INJECTION-MOLDED PARTS

被引：6
|
作者：
MOORE, JA
JARDING, BP
LOGRASSO, BK
ANDERSON, IE
机构：
[1] Ames Laboratory, Metallurgy and Ceramics Div., Iowa State University, Ames, Iowa
来源：
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE | 1995年 / 4卷 / 03期
关键词：
DEBINDING; SINTERING; INJECTION MOLDING;
D O I：
10.1007/BF02649064
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Atmosphere control during debinding of powder injection molded (PIM) parts is an important parameter to consider. Experimental results have shown that a stagnant atmosphere containing volatiles evolved during debinding can cause slumping of the green samples. Removal of volatiles from the sample zone aids debinding and can reduce cycle times and improve sample quality. Residual carbon and oxygen can be controlled during debinding by adjusting the atmosphere composition. This paper presents the results of PIM 70 vol% spherical copper powder and 30 vol% binder. Debinding atmospheres were altered to determine the effect of debinding on the green body and the sintered sample.
引用
收藏
页码：275 / 282
页数：8
相关论文
共 50 条
  • [21] Numerical and experimental evaluation of surface properties of embossed decorative injection-molded parts
    Thanh Binh Nguyen Thi
    Yokoyama, Atsushi
    Hamanaka, Senji
    Kodama, Katsuhiro
    Yamashita, Katsuhisa
    Nonomura, Chisato
    POLYMER TESTING, 2016, 53 : 188 - 196
  • [22] Direct-search-based automatic minimization of weldlines in injection-molded parts
    Yao, DG
    Kim, B
    POLYMER-PLASTICS TECHNOLOGY AND ENGINEERING, 1998, 37 (04) : 509 - 525
  • [23] Methods for automated manufacturability analysis of injection-molded and die-cast parts
    Bidkar, Rahul A.
    McAdams, Daniel A.
    RESEARCH IN ENGINEERING DESIGN, 2010, 21 (01) : 1 - 24
  • [24] Distribution of material in an injection-molded container
    Aasetre, S
    Andreassen, E
    ANTEC '99: PLASTICS BRIDGING THE MILLENNIA, CONFERENCE PROCEEDINGS, VOLS I-III: VOL I: PROCESSING; VOL II: MATERIALS; VOL III: SPECIAL AREAS;, 1999, : 3931 - 3935
  • [25] Prediction of Fiber Orientation in Injection-Molded Parts Using Three-Dimensional Simulations
    Wang, Jin
    Cook, Peter
    Bakharev, Alex
    Costa, Franco
    Astbury, David
    PROCEEDINGS OF PPS-31: THE 31ST INTERNATIONAL CONFERENCE OF THE POLYMER PROCESSING SOCIETY, 2016, 1713
  • [26] The Potential of an Itaconic Acid Diester as Environmentally Friendly Plasticizer for Injection-Molded Polylactide Parts
    Ivorra-Martinez, Juan
    Angel Peydro, Miguel
    Gomez-Caturla, Jaume
    Boronat, Teodomiro
    Balart, Rafa
    MACROMOLECULAR MATERIALS AND ENGINEERING, 2022, 307 (12)
  • [27] An Investigation to Reduce the Effect of Moisture on Injection-Molded Parts through Optimization of Plasticization Parameters
    Chen, Shia-Chung
    Su, Han
    Mathew, Jibin Jose
    Gunawan, Hariyanto
    Huang, Chun-Wei
    Feng, Ching-Te
    APPLIED SCIENCES-BASEL, 2022, 12 (03):
  • [28] INFLUENCE OF MOLDING CONDITIONS ON THE FORMATION OF MICROSCOPIC FLOW MARKS ON THE SURFACE OF INJECTION-MOLDED PARTS
    YOSHI, M
    KURAMOTO, H
    KOBUNSHI RONBUNSHU, 1992, 49 (03) : 241 - 248
  • [29] A new partially isostatic method for fast debinding of low-pressure injection molded ceramic parts
    Zorzi, JE
    Perottoni, CA
    da Jornada, JAH
    MATERIALS LETTERS, 2003, 57 (24-25) : 3784 - 3788
  • [30] Debinding and sintering processes of injection molded pure molybdenum
    Li Kun
    Tan Zhaoqiang
    Hou Haitao
    Li Dunxin
    RARE METAL MATERIALS AND ENGINEERING, 2008, 37 (08) : 1456 - 1460
12345